Symbols And Safety Warnings; Main Components; Assembly (Explanations On How To Remove The Packaging And Assemble Detached Parts) - EMAK BC 270 Manuel D'utilisation Et D'entretien

considered improper and therefore a
source of risk to people and property.
2. SYMBOLS AND SAFETY WARNINGS (Fig.24)
1 - Read operator's instruction book before
operating this machine.
2 - Wear head, eye and ear protection.
3 - Wear strong boots and gloves when cutting
with metal or plastic blades.
4 - Be aware that objects can be thrown.
5 - Keep bystanders away 15 m.
6 - WARNING! – The surface can be hot!
7 - Warning! Kickback it's danger.
8 - Purge Bulb.
9 - Type of machine: BRUSH CUTTER.
10 - Guaranteed sound power level.
11 - CE conformity marking.
12 - Serial number.
13 - Year of manufacture.
14 - Max. speed of output shaft, RPM.
15 - Do not use the brushcutter with the wood
cutting disk.
3. MAIN COMPONENTS (Fig.1)
1÷3 - Tools supplied
4 - Harness
5 - Bevel gear
6 - Curved guard
7 - Nylon line head
8 - Fuel tank cap
9 - Purge Bulb
10 - Muffler guard
11 - Spark plug
12 - Air filter
13 - Starter Handle
14 - Choke Lever
15 - Throttle trigger lockout
16 - STOP button
17 - Throttle lever
18 - Harness attachment
19 - Handle
20 - Shaft arm
21 - Button half-throttle
4. ASSEMBLY
FITTING THE SAFETY GUARD (Fig.7)
Fit the blade guard (A) to the shaft arm with screws
in a position allowing the operator to work safely (B).
NOTE: use the guard (C) only with nylon head.
Secure the guard (C) to the protection (A) by
means of the screw (D).
FITTING THE NYLON LINE HEAD (Fig. 8)
Put the upper (F) flange in place. Put the head fixing
pin (H) in the appropriate hole (L) and tighten the
head (N) anti-clockwise by hand.
FITTING THE DISK (Fig. 9)
Fix the blade (R) onto the upper flange (F) making
sure that the rotation direction is correct.
Fix the lower flange (E), the cup (D) and tighten bolt
(A) anti-clockwise.
Put the pin provided in the appropriate hole (L)
to block the blade and allow the bolt (A) to be
tightened to 2.5 kgm (25 Nm).
WARNING – Collar (see arrows C, Fig.9)
must locate in blade's mounting hole.
FITTING THE HANDLE (Fig. 2)
Fit the handle onto the shaft arm and secure it
using screws (A). The handle position is calculated
depending on the requirements of the operator.
ASSEMBLING THE SAFETY BOOM (Fig. 5)
When using the disc instead of nylon line head, it
is necessary to set up the "safety boom". Fix the
boom (A) under the attachment (C) of handle (19B,
Fig. 1) by means of the screws (B). Taking care to
verify the "safety boom" being on the left side of
the brushcutter.
ASSEMBLING THE BIKE HANDLE (Fig. 4)
- Place the bike handle (A, Fig.4) in the lower hub
(B1).
CAUTION: The bike handle (A) must be
fixed onto the hub (B) inside the two notches
(C) indicated on the bike handle.
- Place the upper hub (B2) in position and tighten
the 4 screws (D), without finally tighten yet.
- Line up the handlebar at a right angle to the
drive tube.
- Tighten down the screws (D) firmly.
MOUNTING THE CONTROL HANDLES (Fig. 6)
- Loosen the screw (G, Fig.6). The nut (H) remains
in the control handle (L).
- Push the control handle (L) (throttle trigger M
GB
25