Publicité
Les langues disponibles
Les langues disponibles
OPERATION
To reduce the risk of injury, always
WARNING
wear safety goggles or glasses
with side shields.
Selecting Drill or Drive Action
(Cat. No. 2805-20)
1. To use the drilling mode, rotate
the torque selector collar until the
drill symbol
appears in line
with the arrow.
2. To use the driving mode rotate
the torque selector collar until the
desired clutch setting appears in
line with the arrow.
The adjustable clutch, when
properly adjusted, will slip at a
preset torque to prevent driving
the screw too deep into different
materials and to prevent damage to the screw or
tool.
Selecting Hammer, Drill or Drive Action
(Cat. No. 2806-20)
1. To use the hammer-drilling
mode, rotate the torque selector
collar until the hammer symbol
appears in line with the ar-
row. Apply pressure to the bit to
engage the hammering mecha-
nism.
NOTE: When using carbide bits, do not use water
to settle dust. Do not attempt to drill through steel
reinforcing rods. This will damage the carbide bits.
2. To use the drilling only mode,
rotate the torque selector collar
until the drill symbol
in line with the arrow.
NOTE: The number selected on
the torque selector collar has no
effect on operation of the drill in drilling mode.
3. To use the driving screws
mode rotate the torque selector
collar until the desired clutch set-
ting appears in line with the ar-
row.
The adjustable clutch, when
properly adjusted, will slip at a preset torque to
prevent driving the screw too deep into different
materials and to prevent damage to the screw or
tool.
The torque specifications shown here are approxi-
mate values obtained with a fully charged battery
pack.
TORQUE SPECIFICATIONS
Clutch
Setting in. lbs
1-4
25-40
Small screws in softwood.
5-8
45-60
Medium screws in softwood
9-11
65-75
or small screws in hardwood.
12-14
80-90
NOTE: Because the settings shown in the table are
only a guide, use a piece of scrap material to test
the different clutch settings before driving screws
into the workpiece.
appears
Applications
Mode Selector
Selector
button
Anti-
Kickback
Control
Indicator
Allow the tool to come to a complete stop before
changing modes. Press the selector button
cycle between the settings. When the tool is con-
nected to the ONE-KEY App™, the indicator will
blink blue. Select wireless
RPM, BPM, and anti-kickback control settings via
the ONE-KEY™ App on your smart device. Mode 1
defaults to 500 RPM with anti-kickback ON, Mode 2
to 1200 RPM with anti-kickback OFF and Mode 3 to
2000 RPM with anti-kickback OFF.
When anti-kickback control is on, the
solid green. If the tool detects a sudden twisting mo-
tion, the tool will shut off and the
green.
Selecting Speed
The speed selector is on top of the motor housing.
Allow the tool to come to a complete stop before
changing speeds. See "Applications" for recom-
mended speeds under various conditions.
1. For Low speed, push the speed selector to display
"1".
2. For High speed, push the speed selector to display
"2".
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
Forward
Push to CENTER
For forward (clockwise) rotation, push in the control
switch from the right side of the tool. Check the
direction of rotation before use.
For reverse (counterclockwise) rotation, push in the
control switch from the left side of the tool. Check
direction of rotation before use.
To lock the trigger, push the control switch to the
center position. The trigger will not work while the
control switch is in the center locked position. Always
lock the trigger or remove the battery pack before
performing maintenance, changing accessories,
storing the tool and any time the tool is not in use.
5
Modes
1, 2, 3
ONE-KEY™
Indicator
to change the default
light will be
light will blink
Reverse
LOCK
to
Publicité
