Bosch GNF 65 A Professional Notice Originale page 17

OBJ_BUCH-1725-002.book Page 17 Friday, August 26, 2016 3:12 PM
8 Protection guard with cutting guide
9 Clamping lever for depth stop adjustment
10 Vacuum connection
11 Elbow
12 Vacuum hose*
13 Screw
14 Clamping lever for protection guard
15 Grinder spindle
16 Mounting flange
17 Diamond cutting disc*
18 Spacer discs
19 Clamping nut
20 Two-pin spanner for clamping nut*
21 Break-out tool*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Wall Chaser
Article number
Rated power input
Output power
No-load speed min
Max. diameter for diamond
cutting discs mm
Working with one diamond
cutting disc
– Cutting discs width, min. mm
– Cutting discs width, max. mm
Working with two diamond
cutting discs
– Cutting discs width, min. mm
– Cutting discs width, max. mm
Mounting bore mm
Slot depth mm
Slot width mm
Weight according to EPTA-
Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Measured values determined according to EN 60745 (lime-
sand brick).
Typically the A-weighted noise levels of the product are:
Sound pressure level 97 dB(A); Sound power level
108 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a =9.0 m/s , K<2.0 m/s .
h
Bosch Power Tools
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
GNF 65 A
scribed under "Technical Data" is in conformity with all rele-
0 601 368 7..
vant provisions of the directives 2011/65/EU, 2014/30/EU,
W 2400
2006/42/EC including their amendments and complies with
the following standards: EN 60745, EN 50581.
W 1670
-1 Technical file (2006/42/EC) at:
5200
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
230
Henk Becker
Executive Vice President
Engineering
2.3
2.8
2 x 2.3
Robert Bosch Power Tools GmbH
2 x 2.8 70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
22.2
20 – 65
Assembly
8 – 40
 Before any work on the machine itself, pull the mains
plug.
kg 8.4
Dust Extraction
/II
 Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suita-
ble for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
English | 17
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 2PN | (26.8.16)