Publicité
Les langues disponibles
Les langues disponibles
11 Device Information
1
Type and order code
2
Design
2.1
Controller
2.2
Thermal energy metering
2.3
Installation location / degree of protection according to EN 60529
2.4
Performance levels
2.5
Frost protection condensate tray / heating water
3
Operating limits
2
3.1
Heating water flow / return
Air (heat source)
4
Performance data / flow rate
4.1
Heating water flow rate / internal pressure differential
4
4.2
Heat output / COP
4.3
Sound power level according to EN 12102
Normal operation/reduced operation
4.4
Sound pressure level at a distance of 10 m
Normal operation/reduced operation
4.5
Air flow
5
Dimensions, connections and filling quantities
5.1
Device dimensions without connections
5.2
Device connections for heating system
5.3
Weight of the transportable unit(s) incl. packaging
5.4
Refrigerant; total filling weight
5.5
Lubricant; total filling quantity
6
Electrical connection
6.1
Supply voltage; fuse protection
6.2
Starting current with soft starter
6.3
Nominal power consumption A2 W35/ max. power consumption
6.4
Power consumption ventilator
6.5
Nominal current at A2 / W35 / cos
6.6
Max. power consumption of compressor protection (per compressor) W
7
Complies with the European safety regulations
8
Additional model features
8.1
Type of defrosting
8.2
Max. operating overpressure (heat source/heat sink)
1. The heat circulating pump and the heat pump manager must always be ready for operation.
2. At air inlet temperatures of -25 °C to -15 °C flow temperature rising from 45 °C to 55 °C
3. These data indicate the size and capacity of the system according to EN 14511. For an analysis of the economic and energy efficiency of the system, the bivalence point and
regulation should be taken into consideration. These specifications can only be achieved with clean heat exchangers. Information on maintenance, start-up and operation can be
found in the respective sections of the installation and operating instructions. The specified values have the following meaning, e.g. A7 / W35: Heat source temperature 7 °C and
heating water flow temperature 35 °C.
4. With maximum heating water flow.
5. The heat output is reduced by approx. 5 % in lower operation
6. The specified sound pressure level corresponds to the operating noise of the heat pump in heating operation with a flow temperature of 35 °C.
7. Please note that additional space is required for pipe connections, operation and maintenance.
8. See CE declaration of conformity
www.dimplex.de
1
°C
°C
3
maximum
m³/h / Pa
minimum
m³/h / Pa
at A-7 / W35
kW / ---
at A2 / W35
kW / ---
at A7 / W35
kW / ---
at A7 / W55
kW / ---
at A10 / W35
kW / ---
5
dB(A)
6
5
dB(A)
m³/h
7
H x W x L mm
Inches
kg
type / kg
type / litres
A
3
kW
W
A / ---
bar
452164.66.03 · FD 9211
LA 11MAS - LA 16MAS
LA 11MAS
External
-
Outdoor / IP24
1
Heated / yes
up to 55 ± 2 / from 18
-25 to +35
1,7 / 7600
0.7/ 1600
EN 14511
5.7 / 2.8
7.9 / 3.4
9.5 / 3.9
8.2 / 2.9
10.4 / 4.2
63 /61
33 / 31
3000
1340 x 852 x 1050
R1"
189
R404A / 3.8
Polyolester (POE) / 1.3
1~/N/PE 230 V (50 Hz) / C20 A
29
2.3 / 3.6
up to 85
12.5 / 0.8
-
8
Reverse circulation
3.0
LA 16MAS
External
-
Outdoor / IP24
1
Heated / yes
up to 55 ± 2 / from 18
-25 to +35
2,6 / 14800
1.2/ 4900
EN 14511
9.8 / 2.6
11.9 / 3.1
14.5 / 3.7
13.5 / 2.4
15.5 / 3.9
64 / 61
34 / 31
4500
1550 x 852 x 1074
R1"
229
R404A / 3.8
Polyolester (POE) / 1.9
1~/N/PE 230V (50 Hz) / C32 A
45
3.8/ 6.1
up to 180
20.7 / 0.8
-
8
Reverse circulation
3.0
EN-9
Publicité
Chapitres
