Installation Requirements; Tools And Parts; Options; Location Requirements - Whirlpool WHP1000SQ Guide D'utilisation Et D'entretien

Tools and Parts

Gather the required tools and parts before starting installation.
The parts supplied are in the washer drum.
Tools needed for connecting the water inlet hoses
■ Pliers (that open to 1 9 /
16
■ Flashlight (optional)
Tools needed for connecting the drain hose
■ Locking pliers (that open to 1
Tools needed for installation
■
Open end wrenches 14 mm and 13 mm
■ Level
■
Wood block
■ Ruler or measuring tape
Parts supplied
A
E F
A. Drain hose form
B. Inlet hose (2)
C. Inlet hose washer (4)
D. Drain hose
Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, call the toll-free number
on the cover or in the "Assistance or Service" section.
If You Have You Will Need to Buy
Laundry tub or Sump pump system (if not already
standpipe taller available)
than 96" (2.4 m)
Overhead sewer Standard 20 gal. (76 L), 30" (762 mm) tall
drain tub or utility sink and sump pump
(available from local plumbing suppliers)
Floor drain Siphon break, Part Number 285834;
additional drain hose
Part Number 8318155; and connector
kit, Part Number 2858835
Drain hose too 4 ft (1.2 m) drain hose extension kit,
short Part Number 2858863
Water faucets 2 longer water fill hoses:
beyond reach of fill 6 ft (1.8 m) Part Number 76314
hoses 10 ft (3.0 m) Part Number 350008
4

INSTALLATION REQUIREMENTS

[39.5 mm])
9 / " [39.5 mm])
16
B
C
D
E. Transport bolt hole plug (4)
F. Beaded strap
G. Hose clamp
Pedestal
You have the option of purchasing pedestals of different heights
separately for this washer. You may select a 10" (254 mm) or a
15.5" (394 mm) pedestal. The pedestal will add to the total height
of the washer.
Pedestal
Height
10"
(254 mm)
G
10"
(254 mm)
15.5"
(394 mm)
15.5"
(394 mm)
15.5"
(394 mm)
Stack Kit
Are you planning to stack your washer and dryer? To do so, you
will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your washer or
refer to the "Assistance or Service" section of this manual. Ask for
Part Number 8572546.
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer "walk."
Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area. See "Drain
System."
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will need
■
A water heater set to deliver 120°F (49°C) water to the washer.
■ A grounded electrical outlet located within 6 ft (1.8 m) of
where the power cord is attached to the back of the washer.
See "Electrical Requirements."

Options

Optional pedestal
Approximate Color
Height with
Washer
46" White
(1168 mm)
46" Cranberry
(1168 mm) Red
51.5" White
(1308 mm)
51.5" Cranberry
(1308 mm) Red
51.5" Lunar
(1308 mm) Silver

Location Requirements

Model
Number
WHP1000SQ
XHP1000WR
WHP1500SQ
XHP1550WR
XHP1550WL