Bosch GSC 12V-13 Professional Notice Originale page 11

OBJ_BUCH-2918-001.book Page 11 Tuesday, July 19, 2016 2:46 PM
Technical Data
Cordless Sheet Metal Shear
Article number
Rated voltage
Stroke rate at no load n
0
Max. steel sheet cutting capacity
Smallest curve radius
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
3)
– during operation and during
storage
Recommended batteries
Recommended chargers
2
1) to 400 N/mm with reference to steel sheet
2) depending on the battery pack being used
3) limited performance at temperatures <0 °C
Noise/Vibration Information
Sound emission values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K < 1.5 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-8: a
2
K< 1.5 m/s .
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
Battery Charging
 Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Bosch Power Tools
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
GSC 12V-13
battery charger before using your power tool for the first time.
3 601 J26 1..
The lithium-ion battery can be charged at any time without re-
V= 12
ducing its service life. Interrupting the charging procedure
-1 does not damage the battery.
min 3600
1)
mm 1.3
Battery Charge-control Indication
mm 15 The three green LEDs of the battery charge-control indicator
4 indicate the charge condition of the battery 2. For safety
reasons, it is only possible to check the status of the charge
2)
kg 1.4– 1.6
condition when the machine is at a standstill.
– To indicate the charge condition, press and hold button 3
°C 0...+45
°C –20...+50
LED
GBA 10,8V...
Continuous lighting 3 x green
GBA 12V...
Continuous lighting 2 x green
AL 11.. CV
Continuous lighting 1 x green
GAL 12.. CV
Flashing light 1 x green
Removing the battery
– To remove the battery 2, press the unlocking buttons 1 and
Operation
Starting Operation
Inserting the battery
 Use only original Bosch lithium-ion batteries with the
2
= 3.5 m/s ,
h
Note: Use of batteries not suitable for the machine can lead to
malfunctions of or cause damage to the power tool.
– Insert the charged battery 2 into the handle until it can be
Switching On and Off
– To start the machine, push the On/Off switch 5 forward so
– To switch off the machine, push the On/Off switch 5 to-
To save energy, only switch the power tool on when using it.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Note: If the machine should automatically switch off because
of a discharged or overheated battery, make sure to set the
machine's On/Off switch 5 to off. Charge the battery and al-
low it to cool down before restarting the machine. Otherwise
the battery can become damaged.
of the switched off machine.
pull the battery out of the machine to the rear. Do not ex-
ert any force.
voltage listed on the nameplate of your power tool.
Using other batteries can lead to injuries and pose a fire
hazard.
felt to engage and faces flush against the handle.
that the "I" is indicated on the switch.
ward the rear so that the "0" is indicated on the switch.
English | 11
Capacity
2/3
1/3
<1/3
Reserve
1 609 92A 2MV | (19.7.16)