Black & Decker FSMH1621S Traduction Des Instructions Originales page 9

When you have finished using the hand held steam
u
cleaner, release the trigger switch (3), turn it 'OFF' and
disconnect from the mains supply. Wait until the steam
mop cools down before storing. (approximately five
minutes)
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean,
turn the hand held steam cleaner 'OFF'. Unplug the unit from
the electrical wall outlet, refill the water tank (8).
Caution! Steam may continue to be produced for a short time
after the trigger switch (3) is released, this is normal. Switch
off and allow the unit to cool before removing any accessories.
Accessories
The performance of your appliance depends on the accessory
used. BLACK+DECKER accessories are engineered to high
quality standards and designed to enhance the performance
of your appliance. By using these accessories you will get the
very best from your appliance.
Technical data
Voltage V
ac
Power
W
Tank capacity ml
Weight kg
Troubleshooting
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Problem Step Possible solutions
Check the unit is plugged in at the wall
The steam mop is 1
socket.
not turning on.
Check the unit is switched on using the on/
2
off switch (1).
3 Check the fuse in the plug.
FSMH1621S FSMH16151
(Type 1) (Type 1)
230 230
1600 1600
350 350
3.6 3.6
(Original instructions)
Problem Step Possible solutions
Check that the handle (10) of the steam mop
The digital controls 4
is pushed firmly into the steam mop body (9).
do not light up.
Check that the arrow on the handle is flush
with the top of the steam mop body (9).
Check that the hand held steam cleaner (5)
5
is firmly docked into the steam mop body (9).
6
Check steps 1, then 2, then 3.
The steam mop will only produce steam
The steam mop is 7
once the handle is pulled back from the
not producing
upright position.
steam.
8 Check that the water tank (8) is full.
NOTE: When first filled or after running dry it
can take up to 45 seconds for steam to be
produced.
Check that the Steam head (11) is firmly
9
docked into the steam mop body (9).
10 Check steps 5, then 1, then 2, then 3.
The digital controls 11 Check steps 4, then 5, then 1, then 2, then 3
go out during use.
The steam mop 12
Check steps 7, then 8, then 9, then 5, then 3.
stops producing
steam during use.
The steam mop has 3 settings. Press the
The steam mop is 13
autoselect button (6) to reduce the amount of
producing too
steam being produced.
much steam during
use.
Check that the steam burst button (25) has
14
not been pressed.
The steam mop has 3 settings. Press the
The steam mop is 15
autoselect button (6) to increase the amount
producing too little
of steam being produced.
steam during use.
Press the steam burst button (25) to
16
temporarily increase the amount of steam.
The hand held steam cleaner has a lock off
No steam is being 17
feature. Lift the lock off switch (2) and pull
produced from the
the trigger switch (3). After a few seconds
hand held steam
steam will be produced.
cleaner when the
trigger is pulled.
18
Check steps 8, then 1, then 2, then 3.
The hand held steam cleaner will begin to
The hand held 19
produce steam after 15 seconds and will
steam cleaner is
reach maximum steam flow after 45
producing too little
seconds.
steam during use.
Firmly press the hand held steam cleaner
The hand held 20
release button (20) down, then pull the hand
steam cleaner will
held steam (5) cleaner from the steam mop
not come out from
body (9).
the steam mop
body.
ENGLISH
9