Black & Decker FSMH1621S Traduction Des Instructions Originales page 6

ENGLISH
Note: Ensure the filler cap is firmly secured.
Note: Do not use chemical cleaners with your steam mop..
Attaching the carpet glider (Fig. G) (For use on
carpets only)
Place carpet glider on the floor.
u
Attach a cleaning pad to the unit.
u
Lightly press the steam mop down onto the carpet glider
u
(14) until it clicks into place.
Caution! Always place your steam mop with the handle (10)
in the upright position when stationary and make sure the
steam mop is turned off when not in use.
Removing the carpet glider (Fig. G)
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
Return the handle (10) to the upright position and turn the
u
steam mop 'OFF'.
Wait until the steam mop cools down. (approximately five
u
minutes)
Place the front of your shoe onto the carpet glider removal
u
tab (22) and press down firmly.
Lift the steam mop up off the carpet glider (14).
u
Caution! Always place your steam mop with the handle (10)
in the upright position when stationary and make sure the
steam mop is turned off when not in use.
Fitting a scent pack (Fig. I & J)
Warning! Return the handle (10) to the upright position and
turn the steam mop 'OFF'. Wait until the steam mop cools
down. (approximately five minutes).
Slide the door release button (26), the door will open.
u
Place the scent pack into the cavity (27).
u
Close the door (28) py pushing it firmly down.
u
Attaching the hose and accessories to the Hand
held steam cleaner (Fig. K & L)
Warning! Inspect the seal (26) on the steam nozzle (4) and
hose (27) before each use. If the seal is missing or damaged
then please contact your nearest authorised repair agent. Do
not use the appliance.
Attaching the hose (Fig. K)
Press in the clips (28) on either side of the hose (27).
u
Press the hose (27) onto the steam nozzle (4) and release
u
the clips (28).
Important! Ensure that the hose (27) is securely fastened
before using the hand held steam cleaner. If steam escapes
from the joint then the hose is not correctly fit, allow the unit to
cool then remove and re-fit the hose.
6
(Original instructions)
Attaching the variable steam jet nozzle (Fig. L)
Press in the clips (30) on either side of the variable steam
u
jet nozzle (31).
Press the variable steam jet nozzle onto the steam nozzle
u
(4) or the hose (27) and release the clips (30).
Important! Ensure that the variable steam jet nozzle (31) is
securely fastened before using the hand held steam cleaner.
If steam escapes from the joint then the variable steam jet
nozzle is not correctly fit, allow the unit to cool then remove
and re-fit the variable steam jet nozzle.
Attaching other accessories (Fig. J)
Align the lugs on the hose with the recesses on the acces-
u
sory.
Press the accessory (29) onto the hose (27) and twist
u
anti-clockwise until the accessory clicks into place.
Note! The variable steam jet nozzle may be used without the
hose by fitting them directly to steam nozzle. All other acces-
sories must be connected to the hose for use.
Removing the hose and accessories(Fig. K & L)
Warning! The Steam nozzle, variable steam jet nozzle, hose
and accessories become hot during use. Allow the unit and all
accessories to cool before removing any accessories.
Removing an accessory (Fig. K)
Twist the accessory (29) clockwise then pull away from
u
the hose (27).
Removing the hose (Fig. K)
Press in the clips (29) on either side of the hose (27) and
u
pull away from the steam nozzle (4).
Removing the variable steam jet nozzle (Fig. L)
Press in the clips (30) on either side of the variable steam
u
jet nozzle (31) and pull away from the steam nozzle (4).
Use
Important! This unit will kill 99.9% of bacteria & germs when
used in accordance with this manual and with the micro fibre
pad fitted and a continuous run time of 90 seconds.
Switching on and off (Steam mop)
To switch the appliance on, press the ON/OFF button (1).
u
It takes approximately 15 seconds for the steam mop to
heat up.
Note: When the steam mop is first turned on the water res-
ervoir will glow red. Once the steam mop is ready to use the
water reservoir will glow blue.
To switch the appliance off, press the ON/OFF button (1).
u