Scheppach DP18VARIO Traduction De La Notice Originale page 23

• CAUTION!
- The use of other bits and other accessories can result
in a risk of personal injury.
• Have your power tool be repaired by a qualified
electrician
- This power tool complies with the relevant safety re-
gulations. Repairs may only be performed by a quali-
fied electrician, using original spare parts; otherwise
accidents involving the user may result.
Warning! This electric tool generates an electromagne-
tic field during operation. This field can impair active or
passive medical implants under certain conditions. In
order to prevent the risk of serious or deadly injuries, we
recommend that persons with medical implants consult
with their physician and the manufacturer of the medical
implant prior to operating the electric tool.
Service:
• Have your power tool repaired only by qualified
specialists and only with original spare parts. This
will ensure that the power tool remains safe.
Safety Instructions for Box Column Drills
• Never make the warning labels on the power tool
illegible.
• Attach the power tool to a solid, flat and horizontal
surface. If the power tool can slip or wobble, the bit
may not be guided smoothly and safely.
• Keep the work area clean except for the workpiece
to be machined. Sharp-edged drilling chips and ob-
jects can cause injury. Material mixtures are particu-
larly dangerous. Light metal dust can burn or explode.
• Set the correct speed before starting work. The
speed must be appropriate for the drill diameter
and the material to be drilled. At an incorrectly set
speed the bit may get jammed in the workpiece.
• Only when the device is turned on should the bit
be moved against the work piece. Otherwise there
is a danger that the bit will get jammed in the work-
piece and the workpiece will rotate with the bit. This
can lead to injuries.
• Do not put your hands in the area of the drill while
the power tool is running. Upon contact with the bit
is a risk of injury.
• Never remove drilling chips from the drilling area
while the power tool is running.Always put the drive
mechanism in the standby position first and then turn
on the power tool.
• Do not remove accumulated drill chips with your
bare hands. There is a risk of injury due to hot and
sharp metal shavings in particular.
• Break up long drilling chips by interrupting the
drilling operation with a short backward rotation of
the rotary wheel. Long drilling chips may cause injury.
• Keep handles dry, clean and free from oil and gre-
ase. Greasy, oily handles are slippery and lead to loss
of control.
• Use clamps to hold the workpiece in place. Do
not work on any workpieces that are too small for
clamping. If you hold the workpiece by hand, you
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
cannot hold it sufficiently tightly against rotation and
may hurt yourself.
• Switch the power tool off immediately if the bit
jams. The bit jams when:
- the power tool is overloaded or
- the workpiece to be machined is jammed.
• Do not touch the bit after working before it has
cooled down. The bit is very hot during use.
• Inspect the cable regularly and have a damaged
cable repaired only by an authorised customer ser-
vice centre. Replace damaged extension cables.
This will ensure that the power tool remains safe.
• Store unused power tools in a safe place. The sto-
rage place should be dry and lockable. This pre-
vents the power tool from being damaged as a result
of being stored or operated by inexperienced people.
• Never leave the tool before it has come to a com-
plete standstill. Afterrunning bits can cause injury.
• Do not use the power tool with a damaged cable.
Do not touch the damaged cable and pull the
mains plug if the cable is damaged while working.
Damaged cables increase the risk of electric shock.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with unpro-
tected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting surfaces
and persons or animals. Even a laser beam with a low
output can cause damage to the eyes.
• Caution - methods other than those specified here can
result in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure
to the beam can occur.
• If the mitre saw is not used for an extended period of
time, the batteries should be removed.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.
23 І 56