Equipment; Fittings Technical Data; Caring For The Steam Bath/Shower Cabin; Caring For The Glass Panes And Profi Les - HOESCH SensaMare Delight Instructions De Montage Et D'utilisation

■ The shower enclosure has been designed for installation on bricked walls. Please strenghten other wall
structures (wood, gypsum board), to ensure a reliable fastening.
■ Please note that in the shower enclosure area only appropriate materials for wall covering must be used.
A ground surface treatment according to moisture stress class FKB 2 is required.
■ Before installation the walls must be completely tiled at the entire cabin hight.
■ The ground surface at the installation location must be perfectly fl at.
■ If the shower enclosure is installed without the shower tray, the client should provide the water outfl ow and
proper slope to water outfl ow. Moreover the proper base for the glass sheet instalation should be ensured.
Therefore the attached template should be used.
⚠
Silicone must be provided by building constructor. Please keep in mind that maintenance joints may
require cleaning.
02

Equipment

■ The back black wall is made of safety glass sheet with EverClean protect coating. Both sides are illuminated.
■ Frameless glazing made of toughened safety glass with EverClean coating.
■ The roof is made of high-quality glass with light colour switch.
■ The shower tray made of mineral cast.
■ Fittings (chrome-plated) consisting of:
hand shower, rain shower, 8 adjustable back jets, thermostat 1/2˝, 1 closing valve.

02.01 Fittings technical data

Minimum fl ow pressure:
Recommended fl ow pressure:
Hot water temperature:
Recommended hot water temperature: 60-70°C
Temperature range:
Safety cut-off:
03

Caring for the steam bath/shower cabin

After showering/steaming, rinse the tray and wall element surface with water and wipe down with a damp cloth. Do not
use scouring agents! For occasional thorough cleaning, use a few drops of cleaning agent, e.g. Hoesch Cleaner (item
no. 6999 00), on the surface and rub with a soft, dry cloth. Remove heavier soiling using warm water and liquid cleaning
agent or a soap lye. Wipe away scale deposits using vinegar and water (avoid contact with the fi ttings!).
Observe the manufacturer's instructions if using drain cleaners!
Remove slight scratches or rough areas in glossy surfaces with the Hoesch Sanicryl care set (item no. 699100, follow
instructions!). Remove deep scratch marks or burns on glossy or matt surfaces using fi ne sandpaper (no. 500) or a fi ne
steel wool metal eraser by rubbing carefully in one direction in a large area around the scratch. Treat glossy surfaces
only with special polishing cream.
03.01 Caring for the glass panes and profi les
■ After showering, quickly rinse the partition with clean water.
■ Use only a damp rag (never dry) to wipe down the panels and frame. You can also use a squeegee to dry the
panels.
■ Only use gentle cleaners such as a weak vinegar and water solution. Never use cleansing powder or cleaners
containing chlorine.
■ Do not use microfi ber cloths. They destroy any coatings and may cause the glass to become scratched.
■ It is a good idea to lightly oil sliding and swinging doors so they remain easy to open.
03.02 Caring for the fi ttings
For day-to-day cleaning, use neutral or citrus-based cleaning agents only. Use cleaning agents intended for cleaning
fi ttings only. Follow the instructions for the cleaning agent!
Spray cleaning agent onto a cloth and use it to clean the fi ttings.
Rinse the fi tting with plenty of water and polish with a soft cloth.

03.03 Do not use ...

■ Scouring or scraping cleaning textiles or sponges.
■ Cleaning agents with fl uid acids such as hydrochloric or citric acid.
■ Scouring agents.
■ Cleaning agents containing chlorine bleach lye.
100 kPa
200-500 kPa
max. 90°C
20-60°C
38°C
GB
7