Avdel eRiv b10 Notice Originale page 14

GB
Switching the device into stand-by mode
Press the trigger (E) for a short time. The white LED for the illumination of the riveting area lights up. The device is thereby switched to stand-by for three minutes.
Pressing the power switch again will reset the stand-by counter to three minutes.
Changing nozzles
The nozzles (A) are marked with numbers corresponding to the rivet cross-section. Hold the power switch (E) pressed, that will lead to the clamping mechanism
moving into the rear position. Use the included wrench SW 11 to switch to the required nozzle and release the power switch.
Riveting
Insert the rivet into the nozzle (A) and the other end of the rivet into the work-pieces to be riveted. Press the power switch until the rivet is removed, then release
the power switch. Tilt the riveting device backwards so that the removed rivet pin falls into the mandrel collection device (D). If the rivet doesn't come off in a
single working stroke, repeat the procedure.
Failure
If rivets which exceed the indicated power of the device are used or if the battery is empty or overloaded, the device will stop operating and the red LED (C) will
light up. Wait until the red LED (C) goes out and press the power switch (E) for a short time. The device will revert to the original position.
If the battery is empty, the device is powered down by a protective circuit and the working tool doesn't move any more.
Don't press the power switch again after the electric riveting machine has been powered down automatically, this may lead to battery damage.
Changing the clamping jaw (>> page 3)
The clamping jaws are wearing parts. If you are unable to rivet in a single working stroke you should change the clamping jaws:
I. (1) Front sleeve
II. (2) Clamping sleeve
(3) Riveting machine
(4) Clamping jaws (3 parts)
Remove the front sleeve (1) and the clamping sleeve (2) from the device (3) and remove the clamping jaws (4)
from the clamping sleeve (2).
III. Oil the clamping sleeve (2) with Molykote® D grease (5).
IV. Hold the clamping sleeve (2) so that its forward part is faced down.
V. Place the clamping jaws (4) in the clamping sleeve (2) with their smooth sides facing outwards.
VI. Mount the clamping sleeve (2) with the new clamping jaws (4) and finally replace the forward sleeve (1).
Notices on optimal handling of the battery
Keep the battery away from wetness and water. Only store the battery at temperatures from 0° to 45°C. Do not leave the battery in the car, e.g. in summer. If the
battery is working for significantly shorter periods of time after a recharge, it is used up and needs to be replaced.
Please consider the notices for disposal.
Maintenance and service
Take the battery out of the electric riveting machine for transportation and storage.
Risk of injury occurs if you inadvertently press the power switch.
[?] Keep the electric riveting machine and the ventilation slots clean to ensure good and safe operation.
If the electric riveting machine should fail despite the meticulous manufacturing and quality control procedures, the repairs should be done by an authorized service
center for AVDEL electric riveting devices.
Please, quote the serial number indicated on the type label of the electric riveting machine whenever turning to our customer service or ordering spare parts.
Disposal
Electric riveting machines, accessories and packaging should be disposed in a way which makes them available for environment-friendly recycling.
Only valid for European Union countries:
Do not dispose of electric riveting machines in household waste.
According to European regulation 2002/96/EG concerning electric and electronic appliances and its implementation in national laws, the electric riveting machines
that are not functional need to be collected separately to make them available for environment-friendly recycling.
Batteries:
Li-Ion: Do not dispose of batteries in household waste, do not throw them into fire or water. Batteries should be collected and recycled or disposed of in an
environment-friendly way. Only valid for European Union countries: According to European regulation 91/157/EWG, defective and used up batteries need to be
recycled. Batteries that are not functional can be handed over at your store or directly disposed of in an environment-friendly way.
Avdel UK Limited Pacific House
2 Swiftfields
Watchmead Industrial Estate
Welwyn Garden City
Hertfordshire AL7 1LY
Tel.: +44 (0) 1707 292000
Fax.: +44 (0) 1707 292199
Mail.: enquiries@infastech.com
www.avdel-global.com
www.infastech.com
13
14