Publicité
Les langues disponibles
Les langues disponibles
TECHNICAL DATA
BREAKER HAMMER
Production code................................................................................
Rate of percussion under load max. .................................................
Impact energy per stroke according to EPTA-Procedure 05/2009 .....
Tool reception ...................................................................................
Weight according EPTA-Procedure 01/2014 ...................................
Frequency band(s) of Bluetooth .......................................................
Radio-frequency power ....................................................................
Bluetooth version ..............................................................................
Recommended ambient operating temperature ................................
Recommended battery types ............................................................
Recommended charger .....................................................................
Noise information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=1,92 dB(A)) ...........................
Sound power level (Uncertainty K=1,92 dB(A)) ................................
Wear ear protectors!
Vibration information
Total vibration values (vector sum in the three axes) determined
according to EN 60745.
Chiselling:
Vibration emission value a
.....................................................
h, Cheq
Uncertainty K= ...............................................................................
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may signifi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when
it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS FOR BREAKER HAMMER
Wear ear protectors. Exposure to noise can cause hearing loss.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring. Cutting accessory contacting a „live" wire
may make exposed metal parts of the power tool „live" and could
give the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health
(e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not
switch the device on again while the insertion tool is stalled, as
doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
22
ENGLISH
MXF DH2528H
........................ 4681 91 02...
...000001-999999
.......................... 1300 min
-1
.............................. 64 J
.............................. 28 mm
........................... 29,6 kg
................. 2402-2480 MHz
............................. 1,8 dBm
............................. 4.0 BT signal mode
.............. -18°C ... +50 °C
................MXFCP203, MXFXC406
.............................. MXFC
......................... 84,71 dB(A)
......................... 95,71 dB(A)
........................... 5,17 m/s
2
............................. 1,5 m/s
2
WARNING! Danger of burns
• when changing tools
• when setting the device down
When working in walls ceiling, or fl oor, take care to avoid electric
cables and gas or waterpipes.
Remove the battery pack before starting any work on the
machine.
Always keep a safe footing and hold machine with both hands.
Keep children or animals away from working area.
Do not direct the machine towards people standing close whilst it
is operating. The inserted tool could be catapulted out and cause
serious injuries.
Ensure that nobody is at risk of materials being catapulted out or
falling. Always work carefully and attempt to anticipate potential
dangers.
Put down the machine carefully. Do not throw the machine to the
ground or drop it from great heights. If it is thrown to the ground,
the machine may injure others or suff er damage itself.
Do not dispose of used battery packs in the household refuse or
by burning them. Milwaukee Distributors off er to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System MXF chargers for charging System MXF battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in
dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery acid
wash it off immediately with soap and water. In case of eye
contact rinse thoroughly for at least 10 minutes and immediately
seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in fl uid or allow a fl uid to fl ow inside them.
Corrosive or conductive fl uids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., can
cause a short circuit.
WARNING This device contains a lithium button/
coin cell battery. A new or used battery can cause
severe internal burns and lead to death in as little as
2 hours if swallowed or enters the body. Always
secure the battery cover. If it does not close securely,
stop using the device, remove the batteries, and keep it away from
children. If you think batteries may have been swallowed or
entered the body, seek immediate medical attention.
SPECIFIED CONDITIONS OF USE
The hammer can be used for chiselling in stone and concrete.
Do not use this product in any other way as stated for normal use.
TRANSPORT, HANDLING AND STORAGE
The machine is heavy. It may cause serious injuries if it is dropped.
The machine has no lifting or lashing points.
Lift the machine using the additional handle and place it on a
suitable means of transport.
Secure the machine whilst it is being lifted, transported or stored to
prevent it tipping over, falling or slipping.
Always allow the machine to cool down before placing it in storage.
Store the machine in a locked, clean, dry place which is protected
from frost and inaccessible for children.
CHANGING THE TOOL
See the picture section for instructions on changing the tool.
The inserted tool must be suitable for the tool mounting.
The shaft of the inserted tool must be undamaged.
The inserted tool must be adequately sharp to prevent recoil.
The inserted tool must be suitable for the planned work.
After inserting the tool, check whether it has been locked correctly.
ONE-KEY™
To learn more about the ONE-KEY functionality for this tool, please
reference the Quick Start guide included with this product or go to
www.milwaukeetool.com/one-key. To download the ONE-KEY app,
visit the App Store or Google Play from your smart device.
Also, when the product experiences ESD, the Bluetooth
communication will be disconnected. It needs to be reset manually
to recover.
We considered the results to be within our minimum acceptable
performance level according to EN 55014-2 / EN 301489-1 / EN
301489-17.
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and ready to be
confi gured via the ONE-KEY™ app.
Blinking Blue
Tool is actively communicating with the
ONE-KEY™ app.
Blinking Red
Tool is in security lockout and can be unlocked
by the owner via the ONE-KEY™ app.
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and
away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION LI-ION BATTERY
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life.
Under extreme stress the battery electronics switch off the
machine automatically. To restart, switch the machine off and then
on again. If the machine does not start up again, the battery pack
may have discharged completely. In this case it must be recharged
in the battery charger.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance
with local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated
to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
WORK WHEN IT'S COLD
If the tool is stored for a long period of time or at cold
temperatures, the lubrication may become stiff and the tool may
not working initially or the working may be weak. If this happens:
1. Insert a bit or chisel into the tool.
2. Run the tool against a scrap piece of concrete.
3. Pull and release the trigger every few seconds.
After 15 seconds to 2 minutes, the tool will start hammering
normally. The colder the tool is, the longer it will take to warm up.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Grease the machine at the lubricating nipple once the service light
lights (see picture section).
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the machine type printed as well as the six-digit No. on the
label and order the drawing at your local service agents or directly
at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
ENGLISH
23
Publicité
