Publicité
Les langues disponibles
Les langues disponibles
Kerf Indicator (Fig. A)
The front of the saw shoe has a kerf indicator
and bevel cutting. This indicator enables you to guide the
saw along cutting lines penciled on the material being cut.
The kerf indicator lines up with the left (inner) side of the
saw blade, which makes the slot or "kerf" cut by the moving
blade fall to the right of the indicator. Guide along the
penciled cutting line so that the kerf falls into the waste or
surplus material.
Mounting and Adjusting the Rip Fence
(Fig. O)
The rip fence
23
is used for cutting parallel to the edge of
the workpiece.
Mounting
1. Slacken the rip fence adjustment knob
rip fence to pass.
2. Insert the rip fence
23
3. Tighten the rip fence adjustment knob
Adjusting
1. Slacken the rip fence adjustment knob
rip fence
23
to the desired width. The adjustment can
be read on the rip fence scale.
2. Tighten the rip adjustment knob
Mounting the Dust Extraction
Port (Fig. A, G)
Your circular saw is supplied with a dust extraction port.
To Install the Dust Extraction Port
1. Fully loosen depth adjustment lever
2. Place the shoe
5
in the lowest position.
3. Push the dust extraction port
upper guard and align with the mounting holes. Secure
dust extraction port to the upper guard using the two
screws
provided.
22
Prior to Operation
•
Make sure the guards have been mounted correctly. The
saw blade guard must be in closed position.
•
Make sure the saw blade rotates in the direction of the
arrow on the blade.
•
Do not use excessively worn saw blades.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. E)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide
9
for vertical
to allow the
24
in the base plate as shown.
.
24
24
and set the
24
.
4
onto the circular saw
21
into the tool handle, align the
3
it into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
and firmly pull the battery pack out of the tool
13
handle. Insert it into the charger as described in the charger
section of this manual.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle
25
and one hand on the auxilliary handle
Rafter Hook (Fig. I)
WARNING: To reduce the risk of serious personal
injury, do not use the tool's rafter hook to hang the
tool from your body. DO NOT use the rafter hook for
tethering or securing the tool to a person or object
during use. DO NOT suspend tool overhead or suspend
objects from the rafter hook.
WARNING: To reduce the risk of injury from the
circular saw falling on operators or bystanders, make
sure it is supported securely when using the rafter hook,
or resting in a secure and stable location when not in
use. Be sure to keep the area below clear to reduce the
risk of the tool or off‑cut material falling and striking
someone or something below.
The circular saw has a convenient rafter hook
it to hang on a suitable, stable structure between uses. The
rafter hook is not for tethering or securing the tool to a
person or object during use when elevated.
Workpiece Support (Fig. F, L–M)
WARNING: It is important to support the work properly
and to hold the saw firmly to prevent loss of control
which could cause personal injury. Figure F illustrates
proper hand support of the saw. Maintain a firm grip
with both hands on the saw and position your body
and arm to allow you to resist kickback if it occurs.
ALWAYS TURN OFF TOOL AND REMOVE BATTERY
BEFORE MAKING ANY ADJUSTMENTS!
Figure M shows proper sawing position. Note that hands are
kept away from cutting area. To avoid kickback, DO support
board or panel NEAR the cut (Fig. L). DON'T support board or
panel away from the cut (Fig. L).
Place the work with its "good" side – the one on which
appearance is most important – down. The saw cuts upward,
so any splintering will be on the work face that is up when
you cut it.
Cutting (Fig. N–P)
Place the wider portion of the saw shoe on that part of the
workpiece which is solidly supported, not on the section
that will fall off when the cut is made. As an example,
Figure M illustrates the RIGHT way to cut off the end of a
board. Always clamp work. Don't try to hold short pieces
English
12
.
17
that allows
13
Publicité
