Unold 68415 Notice D'utilisation page 40

BACKEN/Bake To bake separately prepared yeast
or cake dough (by hand or in the
program-me TEIG). This program-
meis not fitted for special prepara-
tions such as choux pastry mixture
or short-crust pastry).
TEIG SCHNELL/ For the fast preparation of yeast
Dough fast dough - e. g. dough for pizza, with-
out baking function
In some programs (BASIS, WEISSBROT, VOLLKORN,
HEFEKUCHEN und BACKPULVER) several beeps during
the second kneading phase remind you to add more ingre-
dients such as nuts, seeds, dried fruit etc. Just open the
lid, add the ingredients and close the lid again.
BRÄUNUNG/CRUST
To select the browning degree of the crust: HELL/LIGHT,
MITTEL/MEDIUM or DUNKEL/DARK, available in all pro-
grams except TEIG, KONFITÜRE and TEIG SCHNELL. The
respective setting is indicated by an arrow in the LCD dis-
play.
STUFE/SIZE
This enables the following setting in the various programs:
ST. I / SIZE I = for a small bread weight, approx. 750-
1.000 g
ST II / SIZE II = for a larger bread weigh, approx. 1.200 g
Please note, that this option is only available in the pro-
grams BASIS, VOLLKORN, HEFEKUCHEN. The respective
setting is indicated by an arrow in the LCD display. Please
note also our recommendations in the recipes.
PAUSE FUNCTION
The button PAUSE allows to interrupt the program, e. g. for
removal of the kneading blade or to brush the surface etc.
Press the button PAUSE for 1 second in order to interrupt
the programme. The display starts to blink. Now you can
open the breadmaker e.g. to remove the kneading blade.
Then close the lid and press the button PAUSE again for
about 1 second. The display stops blinking and the pro-
gramme is continued.
Attention: Do not interrupt the programme for more than
5 minutes. In case of longer interruptions the rising of the
dough may be disturbed.
As long as the PAUSE function is activated (blinking dis-
play) the START/STOPP button is without function and the
programme cannot be stopped completely.
40 von 196
Copyright UNOLD AG | www.unold.de
LIGHT
The interior of the breadmaker
TOP EDITION is fitted with a light-
ing, which allows to follow the ac-
tual state of the programme without
opening the lid. Just press the but-
ton LICHT and the light turns on. To switch off the light
just press the button again. After 1 minute the light is
automatically switched off.
EIGENPROGRAMM/USER PROGRAM
In addition to the other numerous programs provided by
the BACKMEISTER you can also program your own USER
®
PROGRAM. You can change the basic time and program
phase settings as programmed at the factory or leave out
various program phases. This allows you to develop your
own individual program for baking bread or preparing
dough. Below you will find a sample recipe.
First you should become familiar with the following infor-
mation on the basic programming and use of the USER
PROGRAM.
USER PROGRAM
The program features the following options
Browning programmable
Timer programmable
Loaf size I and II not programmable
The default program is the same as for the BASIC program.
Phase Preset
Total time 3:00 hours
Knead 1 10 minutes
Rise 1 20 minutes
Knead 2 15 minutes
Rise 2 25 minutes
Rise 3 45 minutes
Bake 45 minutes
Keep warm 60 minutes
The times can be programmed as shown in the table.
Proceed as follows:
Select the USER PROGRAM with the Menu button.
Programmable time frame
6-14 minutes
20-60 minutes
5-20 minutes
5-120 minutes
0-120 minutes
0-80 minutes
0-60 minutes
Stand 31.7.2020