Publicité
Les langues disponibles
Les langues disponibles
19. CHECK DAMAGED PARTS. Before further use of
the tool, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function - check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade or cutter
against the direction of rotation of the blade or cutter only.
21. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Do not leave tool until it
comes to a complete stop.
22. REPLACEMENT PARTS. When servicing, use
only identical replacement parts.
23. POLARIZED PLUGS. To reduce the risk of electric
shock, this appliance has a polarized plug (one
blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
Ampere Rating
More Than
Not More Than
0
6
10
12
ADDITIONAL SAFETY RULES
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to table saw safety rules. If you use this tool unsafely
or incorrectly, you can suffer serious personal injury.
1.
Wear eye protection.
Do not use the tool in presence of flammable
2.
liquids or gases.
3.
NEVER use the tool with an abrasive cut-off
wheel installed.
4.
Check the blade carefully for cracks or damage
before operation. Replace cracked or damaged
blade immediately.
5.
Clean the spindle, flanges (especially the
installing surface) and hex nut before install-
ing the blade. Poor installation may cause
vibration/wobbling or slippage of the blade.
6.
Use saw-blade guard and riving knife/spreader
and antikickback pawls for every operation
for which it can be used, including all through
sawing operations. Always assemble and
install the blade guard following the step by
step instructions outlined in this manual.
Through sawing operations are those in which
the blade cuts completely through the top of
the workpiece as in ripping or cross cutting.
Table 1: Minimum gage for cord
Volts
120V
6
10
12
16
VOLTAGE WARNING: Before connecting the tool
to a power source (receptacle, outlet, etc.) be sure
the voltage supplied is the same as that specified
on the nameplate of the tool. A power source with
voltage greater than that specified for the tool can
result in SERIOUS INJURY to the user- as well as
damage to the appliance. If in doubt, DO NOT PLUG
IN THE APPLIANCE. Using a power source with
voltage less than the nameplate rating is harmful to
the motor.
USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to
carry the current your product will draw. An under-
sized cord will cause a drop in line voltage resulting
in loss of power and overheating. Table 1 shows the
correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next
heavier gage. The smaller the gage number, the
heavier the cord.
Total length of cord in feet
25 ft.
50 ft.
AWG
18
16
18
16
16
16
14
12
NEVER use the tool with a faulty blade guard
or secure the blade guard with a rope, string,
etc. Any irregular operation of the blade guard
should be corrected immediately.
7.
Immediately raise the riving knife/spreader to the
Spreader position and reattach the guard assem-
bly and side guards, after completing an opera-
tion which requires removal of the guarding.
Do not cut metal objects such as nails and
8.
screws. Inspect for and remove all nails,
screws and other foreign material from the
workpiece before operation.
Remove wrenches, cut-off pieces, etc. from the
9.
table before the switch is turned on.
10. NEVER wear gloves during operation.
11.
Keep hands out of the line of the saw blade.
12. NEVER stand or permit anyone else to stand in
line with the path of the saw blade.
13. Make sure the blade is not contacting the
riving knife/spreader or workpiece before the
switch is turned on.
14. Before cutting an actual workpiece, let the tool run
for a while. Watch for vibration or wobbling that could
indicate poor installation or a poorly balanced blade.
15. NEVER make any adjustments while tool is
running. Disconnect tool before making any
adjustments.
3 ENGLISH
100 ft.
150 ft.
16
14
14
12
14
12
Not Recommended
Publicité
