steute Wireless Safety System sWave 2.4 GHz-safe Instructions De Montage page 6

Table des Matières

Publicité

Wireless Safety System sWave ® 2.4 GHz-safe
//
Montage- und Anschlussanleitung / Sicheres Funksystem
Mounting and wiring instructions / Wireless safety system
Instructions de montage et de câblage / Système radio de sécurité
Istruzioni di montaggio e collegamento / Sistema wireless di sicurezza
Instruções de montagem e instalação / Sistema wireless seguro
Инструкция по монтажу и подключению / Надежная радиосистема
English
5010
CPU to CPU: Wireless telegram switching
state different
5013
Relays do not switch correctly - Timeout
5018
Battery discharged (foot switch)
Configuration, operating elements and displays
For the configuration and display of the connection status, the switch
position and the error codes, there are 2 push-buttons and 5 LEDs on
the receiver. Press both push-buttons (S1/S2) approximately 5 s during
the start-up phase in order to configure the receiver. Afterwards the
LEDs 1..4 display the value of the first parameter. The mode LED
flashes in time with the parameter number like this: 1 time slowly and
1 to 5 times shortly. Push-button S1 switches to the next parameter,
push-button 2 changes the parameter. Both push-buttons terminates
the configuration.
No.
Parameter
Value range
from
1
Sniff mode
0000b
Timeout [h]
S1
2
Sniff mode
0000b
Timeout
[min]
S1
3
CAN-ID –
0000b
High
S1
4
CAN-ID –
0000b
Low
S1
5
CAN Baud-
0000b
rate
S1
1
Sniff mode
.....
......
S1+S2 End
Description
to
S2
1111b
x * 1 hour
Timeout (Def. = 0)
max. 15 hours
S2
1011b
x * 5 minutes
Timeout (Def. = 0)
max. 55 minutes
S2
0111b
High Nibble of
knot address
max. 0x7F (Def.
0x21)
S2
1111b
Low Nibble of
knot address
max. 0x7F (Def.
0x21)
S2
1000b
0000b=10k;
0001b=20k;
0010b=50k;
0011b=100k;
0100b=125k;
0101b=250k;
0110b=500k;
0111b=800k;
1000b=1M
(Def. 1000b=1M)
Receiver in error switch-off
In case of a hardware fault, the receivers switches to error switch-off,
which is indicated by the error code on LEDs 1..4 and the mode LED
flashing slowly. The module remains in this state until the next Pow-
erUp reset. The relays are switched off and the wireless connection is
deactivated. A defective relay is only detected after a restart by repeat-
ed actuation of the foot switch.
Error
Code (mode LED on)
Timeout CPU1
0001b
Self test CPU1
0010b
Self test CPU2
0011b
VCC test
0100b
StackCheck
0101b
Relay defective
1111b
Receiver in operating state
In normal operating state, the LEDs 1...4 indicate the state of the four
switching contacts of the foot pedal. If the wireless connection is built
up, the mode LED is permanently on. With a faulty wireless connection
the mode LED flashes. The indication changes by pressing the push-
button S1 and displays the wireless and CANBus status.
Mode LED
LED x
ON
LED 1 – on / off
(switch condi-
....
tion, default
display)
LED 4 – on / off
S1
OFF
LED 1 – on /
(status)
flashes
LED 2 – off /
flashes
LED 3 – off
LED 3 – flashes
LED 3 – on
LED 4 – on /
flashes
Notices wireless
The transmission is carried out in the licence-free 2.4 GHz ISM fre-
quency band. (Class 2 Bluetooth 2.4...2.4835 GHz). The wireless mod-
ule conforms to the European directive on radio equipment and tele-
communications terminal equipment 1999/5/EC. Protective require-
ments in regard to electromagnetic compatibility are carried out under
consideration of the harmonised standards EN 301 489-1/17 and EN
6 / 40
Sub code (mode LED off)
0000b
0000b
xxxxb (CPU internal
hardware test)
00xxb (01b=CPU1,
10b=CPU2)
0000b
0001b=K1; 0010b=K2;
0011b=K3; 0100b=K4
Description
Switch 1 actuated / not actuated
....
Switch 4 actuated / not actuated
CAN connection built up / not
connected
CAN bus okay / error
no wireless connection with
switch
wireless connection in sniff
mode (energy-saving)
wireless connection to switch
active
wireless module in reset /
switch is searched

Publicité

Table des Matières
loading

Table des Matières