Bosch BSGL5 Série Mode D'emploi page 51

Changing the filter
Please note: Always switch off the appliance before
!
changing the filter.
Replacing the bag
20*
Figure
● If the dust bag change indicator in the lid is filled
completely when the floor tool is lifted from the floor
with the highest suction level selected, the dust bag
must be changed, even though it may not yet be full.
Even if the dust bag is not full, it may st ill need
changing, due to the type of dust which has been
vacuumed. First check that the nozzle, suction pipe
and flexible hose are not blocked, as this would also
lead to the dust bag change indicator being
triggered.
21
Figure Opening the lid
● Open the lid by moving the locking lever in the
direction of the arrow.
22
Figure
a) Seal the dust bag by pulling the sealing plate, and
remove the bag.
b) Slide the new dust bag into the holder up to the stop.
Please note: the lid will only close if a dust bag has
!
been inserted.
Cleaning the motor protection filter
The motor protection filter should be cleaned regularly
by tapping out the dirt and rinsing.
23*
Figure
● Open the dust bag compartment lid.
● Remove the motor protection filter from
the appliance in the direction of the arrow.
● Disconnect the motor protection filter from the Bionic
filter.*
● Clean the motor protection filter by tapping out the
dirt.
● If it is very dirty, the motor protection filter should be
rinsed. The filter must then be left to dry for at least
24 hours.
Please note: the Bionic filter must not come into
!
contact with water, as this will adversely affect the
correct operation of the filter.
● After cleaning, place the Bionic filter onto the motor
protection filter as necessary and push both filters
into the appliance.
● Close the dust bag compartment lid.
Replacing the Bionic filter
If your appliance is equipped with a Bionic filter, it
should be replaced once it begins to lose its effect
(after approx. 1 year).
24*
Figure
● Open the dust bag compartment lid.
● Remove the motor protection filter together with the
Bionic filter from the appliance.
● Remove the old Bionic filter from the motor
protection filter and dispose of it.
● Place the Bionic filter onto the motor protection filter.
● Push the filters into the appliance and close the dust
● The motor protection filter must also be inserted into
Replacing the exhaust filter
Replacing the micro-hygiene filter
This should be replaced with every replacement filter pack.
Figure
● Open the dust bag compartment lid.
● Release the filter holder by turning the locking lever
● Remove the micro-hygiene filter. Insert the new
● Insert the filter holder in the appliance and lock it in
Cleaning the Hepa* exhaust filter
The Hepa* filter is designed so that it does not need to be
replaced, provided the appliance is used as intended in the
household.
To ensure that the vacuum cleaner is working at its optimum
power level, the Hepa* filter should be rinsed out after one
year. The filtering action of the filter remains intact, even if the
filter surface becomes discoloured.
Figure
● Open the dust bag compartment lid.
● Unlock the Hepa* filter by moving the locking tab in the
● Tap out the filter unit and rinse it under running water.
Figure 21
● Once the Hepa* filter has dried completel y (at least 24
● Close the rear flap.
After vacuuming fine dust particles (e.g. gypsum, cement, etc.),
clean the motor protection filter by tapping it out or, if
necessary, replace the motor protection filter and exhaust
filter.
Care
Always switch off the vacuum cleaner and disconnect
it from the mains before cleaning the vacuum cleaner.
The vacuum cleaner and plastic accessories can be
cleaned with a commercial plastic cleaner.
!
If necessary, the dust compartment can be cleaned
with a second vacuum cleaner or simply wiped with
Figure 21
a dry cloth or dusting brush.
Subject to technical modifications.
* Dependent on model
bag compartment lid.
the appliance if you no longer wish to use the Bionic
filter
25
in the direction of the arrow.
micro-hygiene filter into the appliance.
place.
26*
direction of the arrow, and remove it from the appliance.
Al t ernati v el y , the unit can be cleaned in a washing machine
at max. 30 °C using a gentle programme and the lowest spin
speed.
TIP: To protect other laundry items, put the fil t er unit into a
laundry bag.
hours), insert it back into the appliance and lock it in place.
Do not use abrasive agents, glass or all-purpose
cleaning products. Never immerse the vacuum
cleaner in water.
21
Figure
47