Water Nozzle; Oil Change; Air Filter; Blade - Texas Smart 5105WS Manuel De L'utilisateur

Stop: Illustration F3
1. Release the engine brake and self-propelled bar to
turn off the mower and the engine
Note: The blades will still rotate at up to 3 seconds
after stopping.

Water nozzle

The left side of the mower deck is fitted with a water
nozzle for washing the deck*. (See Illustration ID-F)
•
When using the water nozzle, the machine must be
in the lowest height position and placed on the
lawn. This ensures that the water remains under
the deck during cleaning.
•
Attach a hose to the nozzle.
•
Turn on the water and start the engine.
•
The rotations of the blades will ensure that the
water will clean the underside of the deck.
Note: For best result clean the deck with the water
nozzle function right after each mowing. If the grass
dries out, this function will not work optimally.
* Note: Not all models have water nozzle

Oil change

Oil should be changed for the first time after 5 hours,
then at least 1 time per year.
You will need an oil extractor kit. Art. no. 40-11336
Oil and oil extractor kit is not included
Use an extractor kit and do as follows:
1. Turn on the engine and let it run for 5 min or until
the engine is hot. A hot engine liquefies the oil
which makes it easier to drain.
2. Suck the oil up through the oil filler hole using the
syringe that came with the oil extractor kit. Use the
hose to reach the sump.
3. Transfer the used oil into a empty container.
4. Fill the engine with SAE-30 oil.
5. Check the oil level using the dipstick. (Min / Max)
Remember to dispose the used oil so that it does
no harm to nature. Use your local recycling station.

Air Filter

The air filter should be inspected and cleaned regularly.
If the filter has not been cleaned for a long time, the
engine's power will drop.
See Illustration A2
1. Clean around the air filter before removing the cap.
2. Push the two flaps down and gently pull the cover
3. Carefully remove the paper filter and inspect it.
Brush it with a soft brush. If it is very dirty, replace
it. Be careful that no dirt gets into the inlet.
4. Wash the black foam element in the right side in
warm water and soap.
5. Press the water out of the foam element and let it
dry. Put a few drops of SAE-30 oil on the filter to
moisten it lightly. Carefully squeeze any surplus oil
out of the foam element and reattach.
6. Please note that all parts are assembled correctly
and properly closed, as shown in the picture.

Blade

Inspection of the blade
•
Tilt the mower with the front upwards.
•
Inspect blade for damage, cracks or excessive rust
or corrosion.
•
Check that the blade bolt is tightened.
Note: A dull blade can be sharpened! But a blade that
is worn, bent, cracked or otherwise damaged must be
replaced.
Removing the blade: See illustration A3
If you remove the blade to sharpen or replace it, you
must use a torque wrench and some heavy gloves to
protect your hands.
1. Loosen the blade bolt. Use a piece of wood to
prevent the blade from turning around.
2. Remove the bolt, washer, blade and blade holder
in that order
3. Sharpen or replace the blade.
4. Insert the blade holder, blade, washer and bolt in
that order.
5. Tighten the blade bolt with 50 Nm. Use a piece of
wood to prevent the blade from turning around.
Warning: A blade must be sharpened so it is in
100 % balance, otherwise it may cause vibrations that
could damage the engine. Damage to engine due to
faulty sharpening is not covered by warranty. We
therefore recommend letting a service center sharpen
the blade.

Spark plug

1. Remove the spark plug.
2. Brush off dirt from the spark plug.
3. Use a spark plug wrench to loosen the spark plug.
4. Check the insulation is intact.
5. Clean the spark plug with a wire brush.
6. Measure the electrode, taking care not to damage
the electrode.
7. The distance should be: 0.7 to 0.8 mm
8. If the spark plug is undamaged refit or replace.
Art. no. 40-11294
9. Reattach the spark plug.
7