Quick GENIUS G 600 Manuel De L'utilisateur page 19

POS. DESCRIPTION
12 Key
13 Screw
14 Black pressure lever "G"
15 Spring for pressure lever"G"
16 Screw for pressure lever "G"
17 Plug
18 Washer
19 Idler gear
20 Bearing
21 Plug
22 Screw
23 Anodized "G" capstan base
24 Bearing
25 Circlip
26 Output gear
27 Plug
28 Short shaft
29 Oil seal
30 Anodized "G" capstan cover
31 Assembled sensor
32 Anodized "G" chain guide
33 Screw
34 "G" capstan clutch
35A Gypsy "G" 6 mm
35B Gypsy "G" 7 mm - 1/4"
35C Gypsy "G" 8 mm
35D Gypsy "G" 5/16"
36 Gypsy cover "G"
37 Straight capstan lever
38 Gasket / jig "G"
39 Studs
40 Washer
41 Spring washer
42 Nut
43 Cable
44 Magnet ø8 * 6mm
45 Paper gasket
46 Long shaft
47 Key
48 Distance ring
49 Drum
50 Bush
51 Plug
52 Grower
CODE
MBH020220F00
MBV0516MBCE0
PDLVTD07G000
QUICK™ windlasses are manufactured with materi-
MMTND07G0000
als resistant to marine environments. In any case,
MSMVT07G0000
any salt deposits on the outside must be removed
MBSC10018A00
periodically to avoid corrosion and damage to the
MBR142010X00
equipment. The parts where salt may have built up
MSLRTZ242000
should be washed thoroughly with fresh water.
MBJHK1212000
MBSC12040A00
MBV0550MXCE0
Once a year, the drum and the gypsy are to be tak-
SGMSC07G0000
en apart as follows:
MBJ160060000
MBAE3415Y000
VERSION WITH FREEFALL SYSTEM
MSLRTU442000
Use handle (37) to unscrew the gypsy cover (F);
MBSC08016A00
loosen screw (H) and take off the gypsy cover.
MSAS07129R10
Loosen the screws (33) of the chain stripper (32)
PGPRL3047700
and remove it; remove the gypsy (35).
SGMSG07G0000
SAKREED00000
NO-DRUM VERSION
SGMSN07G0000
Use the handle (37) to remove the gypsy cover (36
MBV0512MXCE0
or F); remove the top clutch cone (34); loosen the
MSF07G000000
fixing screws (33) of the chain stripper (32) and re-
Z S B 0 7 0 6 G 0 0 R 2
move it and pull off the gypsy (35).
Z S B 0 7 0 7 1 4 G R 2
ZSB0708516G0
DRUM VERSION
ZSB070516G00
Use the handle (37) to loosen the bush (50); pull off
MSGB07G00000
MSHD00000000 the drum (49) and the top clutch cone (34); loosen
PGBSG0800000
the fixing screws (33) of the rope/chain stripper
MBP080608X00
(32) and remove it. Pull off the gypsy (35).
MBR08X000000
MBR08XDE0000
Clean all the parts removed to avoid corrosion, and
MBD08MXEN000
grease the shaft thread (28 and 46) and the gypsy
SAECC116G0L0
(35) where the clutch cones rest (use grease suit-
KPMC08060000
able for marine environment) (34).
PGCR07G00000
MSAS07168R10
Remove any oxide deposits from the terminals of
MBH060625F00
the electric motor and the reversing solenoid unit;
MSVCPG080000
grease them.
MSE040000R02
MSD040000R01
MBSC04008A00
MBG05X000000
MAINTENANCE
WARNING:
make sure the electrical power
to the motor is switched off when working
manually on the windlass. Carefully remove
the chain from the gypsy.
GB
19