Bosch GHO 6500 Professional Notice Originale page 15

OBJ_BUCH-2410-002.book Page 15 Thursday, November 19, 2015 11:21 AM
26 Locking nut for angle adjustment*
27 Fastening bolt for rebating depth stop*
28 Rebating depth stop*
29 Park rest
30 Drive belt
31 Large pulley
32 Small pulley
33 Handle (insulated gripping surface)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Planer
Article number
Rated power input
No-load speed
Planing depth
Rebating depth
Planing width, max.
Weight according to
EPTA-Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-14.
Typically the A-weighted noise levels of the product are:
Sound pressure level 86 dB(A); Sound power level 97 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-14:
2 2
a =5.5 m/s , K=1.5 m/s .
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Bosch Power Tools
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-14, EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
GHO 6500
0 601 596 0..
W 650
-1
min 16500
Robert Bosch GmbH, Power Tools Division
mm 0 – 2.6
70764 Leinfelden-Echterdingen, GERMANY
mm 0 – 9
Leinfelden, 19.11.2015
mm 82
Assembly
kg 2.8
 Before any work on the machine itself, pull the mains
/II
plug.
Planer Blade Selection
The power tool can be fitted with different planer blade types.
By using conversion kits (accessory), either planer blade type
(HSS or TC carbide blades) can be used, depending on the
standard equipment of the power tool.
When replacing planer blades, always replace both blades;
otherwise an imbalance can generate vibrations, which can
reduce the service life of the power tool.
Changing HSS Planer Blades
 Be cautious when replacing the planer blades. Do not
grasp the planer blades by the cutting edges. Possible
danger of injury due to the sharp cutting edges of the plan-
er blades.
Disassembling the Planer Blade(s) (see figures A – C)
– To reverse the planer blades, rotate the blade drum 13 un-
til the clamping jaw 12 is parallel to the planer base plate 8.
– Unscrew the 3 fastening screws 11 with the Torx key 10
and remove the clamping jaw 12.
– Slide the planer-blade retainer 16 together with the planer
blade 15 out of the guide groove 14 of the blade drum 13.
– Turn the blade drum by 180° and disassemble the 2nd
planer blade.
Note: Before replacing or resharpening the planer blades, re-
move the HSS planer-blade retainer 16 by loosening the fas-
tening screws 17.
English | 15
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 1T5 | (19.11.15)