Publicité
Les langues disponibles
Les langues disponibles
EN
1. Introduction
Dear customer,
We would like to thank you for choosing a Gebuwin product. You've purchased a professional hoisting product which has been developed, produced and tested
with the greatest care. However, it is our duty to draw your attention to the fact that firstly, it is essential to read these instructions carefully before using this
product and secondly execute them before the product is actually put to use.
Furthermore, we wish to refer you to our website: www.gebuwin.com from which various accessories for this winch can be purchased e.g. complete cable sets
and special drive lubricating grease. In addition, this website provides downloadable information on the following:
-
service information;
user manuals.
-
2. Safety regulations
This theatre winch TW300 is a hand powered rope winch. This winch can be attached to walls or constructions. The winch can only be used for hoisting and/or
lifting goods. The winch has a static safety factor of 8.
The transport (lifting) of persons as well as persons located under a moving load is forbidden.
The winches are not suitable for:
-
continuous use;
motorized drive.
-
The winches without an ATEX option are not suitable for:
use in an area in which aggressive and/or explosive substances are used.
-
Technical alterations and/or the attachment of marginal devices to the winches is only allowed with the manufacturer's (Gebuwin B.V.) written consent.
Servicing, mounting, possible repairs and the maintenance of the winch are permitted only by specialized persons who:
-
have been appointed and authorized;
have been trained;
-
-
are familiar with the correct regulations; and
always use original parts for repairs.
-
2.1. Winch
The winch is equipped with a double load pressure brake for safety reasons. This brake holds the load at any
height and ensures that the load can be lowered in a controlled manner. The first brake, viewed from the worm
gear, operates during normal operation. The second brake comes into action after the first brake has failed, e.g.
due to a broken brake disc.
The load pressure brakes must never be greased or oiled. The braking effect is lost as a result!
The stipulated hoisting capacity calculated on the first cable layer, stated on the type identity sticker must not be
exceeded. The winch must at least be mounted with the required mounting materials from chart 1. The winch must
be inspected/tested by a professional at least once a year.
Never touch moving parts during use!
Always run the following check before you use the winch:
brake function
-
quality of the cable and hoisting parts
-
-
carrier construction
2.2. Load
Pay attention to the following with respect to the load:
-
Secure a load after the load is definitively in place, never leave the load unattended on the winch in a
raised condition for a long time;
-
do not allow the load to swing;
-
never allow the load to fall suddenly from the cable;
ensure that the hoisting height remains in clear view.
-
2.3. Cable and hoisting material(s)
Pay attention to the following with respect to the cable and hoisting material(s):
Use only certified cables according to EN 12385-1, EN12385-2, EN 12385-4 and EN 12385-5 15020 with a min. breaking force from table 1;
-
Cables and load hooks must be regularly checked and maintained in accordance with EN 12384-4;
-
-
Load hooks must have safety valves;
Load hooks must be attached to the cable in accordance with EN 13411, with a sleeve and cable clamp;
-
-
The load must be properly secured.
the lateral run-off angle, the adjustment, may be a maximum of 3
-
degrees;
-
At least 3 safety turns must remain under load on the first layer
of the drum;
-
The top of the last cable layer should be one and a half times the
cable diameter clear of the outer edge of the drum flange;
The cable must be wound onto the drum under pretension;
-
-
Never reach into the cable run-up;
-
Only handle the cable with safety gloves;
Observe the correct cable capacity
-
6
Publicité
