Cleaning, Maintenance And Ordering Of Spare Parts; Carbon Brushes; Ordering Replacement Parts; Disposal And Recycling - EINHELL TH-MS 2513 T Mode D'emploi D'origine

Anleitung_TH_MS_2513_T_SPK1__ 03.05.13 08:07 Seite 21
Using the handle (2), set the turntable (8) to the
n
desired angle, i.e. the marking (a) on the
turntable must coincide with the desired angular
setting (11) on the stationary base plate (9).
Retighten the locking screw (10) to secure the
n
turntable (8) in place.
Cut as described under section 7.2.2.
n
7.2.4 Miter cut 0°- 45° and turntable 0° (Fig. 26/27)
The crosscut and miter saw with table can be used to
make miter cuts of 0° - 45° in relation to the work
face.
Move the machine head to its upper position.
n
Fasten the turntable (8) in 0° position.
n
Undo the tightening screw (22) and use the
n
handle (2) to tilt the machine head to the left until
the pointer coincides with the required angle
value.
Retighten the tightening screw (22) and make
n
the cut as described in section 7.2.2.
7.2.5 Miter cut 0°- 45° and turntable 0°- 45°
(Fig. 25-28)
The crosscut and miter saw with table can be used to
make miter cuts to the left of 0°- 45° in relation to the
work face and, at the same time, 0° - 45° in relation
to the stop rail (double miter cut).
Move the machine head to its upper position.
n
Release the turntable (8) by slackening the
n
locking screw (10).
Use the handle (2) to adjust the turntable (8) to
n
the angle required (in this connection see also
section 7.2.3).
Retighten the locking screw (10) in order to
n
secure the turntable in place.
Undo the tightening screw (22) and use the
n
handle (2) to tilt the machine head to the left until
it coincides with the required angle value (in this
connection see also point 7.2.4).
Screw the tightening screw (22) back down
n
again.
Cut as described under section 7.2.2.
n

8. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
9. Cleaning, maintenance and ordering
of spare parts
Always pull out the mains power plug before starting
any cleaning work.
9.1 Cleaning
Keep all safety devices, air vents and the motor
n
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
n
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
n
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts
of the equipment. Ensure that no water can seep
into the device.

9.2 Carbon brushes

In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician.
Important! The carbon brushes should not be rep
laced by anyone but a qualified electrician.
9.3 Maintenance
There are no parts inside the equipment which
n
require additional maintenance.
Lubricate all moving parts at regular intervals.
n

9.4 Ordering replacement parts

Please quote the following data when ordering
replacement parts:
Type of machine
n
Article number of the machine
n
Identification number of the machine
n
Replacement part number of the part required
n
For our latest prices and information please go to
www.isc-gmbh.info

10. Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.
GB
21