Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
O
E
PTIONAL
QUIPMENT
Optional Equipment Connections
Note:
The remote control must be programmed with supplied
codes to operate the optional equipment (refer to page 9
for programming information).
VCR Connection
VCRs, video disc players, video game equipment, and
DSS equipment can also be connected to the video inputs.
See the optional equipment manual for more information.
Note:
VIDEO 1 input is a dual-purpose input. It is primarily
intended for connection with 480i devices such as a DVD
player using the Y P
Audio L & R jacks. However, it can also be connected to
conventional composite video sources such as a VCR,
using only the Y/Video jack and Audio L & R jacks. The
on-screen label will display Component or Video 1
depending on which source is connected.
TERMINALS ON BACK OF TELEVISION
INPUT 1
R-AUDIO-L
COMPONENT
TO AUDIO
VIDEO INPUT
AMP
P
P
Y/VIDEO
R
B
ANT
L
INPUT 2
S-VIDEO
R
R-AUDIO-L VIDEO
CABLES NOT INCLUDED
Procedure
•
Connect equipment as shown to front or rear Audio/
Video input jacks.
Note:
Do not connect S-VIDEO and VIDEO signal to INPUT 2
at the same time. If both are connected, signal
interference will result. Use either the S-VIDEO or the
Video signal only.
•
Select the Video mode by pressing TV/VIDEO button.
•
Operate optional equipment as instructed in equipment
manual.
Cable Box Connection
Follow this diagram when connecting your television to a
Cable Box.
CABLE BOX
15
ANT IN
ANT OUT
ANT
Incoming
Cable
CABLES NOT SUPPLIED
Procedure
•
Tune the television to channel 3 or 4 depending on the
RF out setting of the cable box.
•
Using the cable box, tune to the premium cable channel
you want to view.
6
C
ONNECTIONS
P
component video jacks and
B
R
VCR
PLAY
R
E
FF
W
STOP
VIDEO OUT
L
AUDIO OUT
R
HPJ
VIDEO 3 L AUDIO IN R
ANT OUT
ANT IN
FRONT A/V JACKS
Incoming
Jack used for 1/8"
Cable
headphone plug
CONNECTION ON BACK OF TV
INPUT 1
R-AUDIO-L
COMPONENT
TO AUDIO
VIDEO INPUT
AMP
P
P
Y/VIDEO
R
B
L
INPUT 2
S-VIDEO
R
R-AUDIO-L VIDEO
Digital TV - Set-Top Box (DTV-STB) or DVD
Player Connection
Use this diagram to connect the Panasonic DTV-STB
(Digital TV-Set-Top Box) to the back of your TV.
CABLES NOT SUPPLIED
TERMINALS ON BACK OF
DTV-STB OR DVD PLAYER
DIGITAL TV OUTPUT
Y
P
P
R-AUDIO-L
B
R
R-AUDIO-L
VIDEO
S-VIDEO
NTSC OUTPUT
Notes:
•
There are three video jacks, Y, P
Separate
component
luminance and color separation. Use the L (left)
and R (right) audio inputs.
•
Select DTV-STB to 480i output mode. TV set can
receive 480i signal only. Picture distortion will result
if any other type of format is selected (i.e. 480p,
720p or 1080i).
Amplifier Connection (TO AUDIO AMP)
To listen the audio through a separate stereo system,
connect an external audio amplifier to TO AUDIO AMP
outputs on back of television.
Note:
TO AUDIO AMP terminals cannot be connected directly
to external speakers.
External Amplifier
CABLES NOT INCLUDED
Audio Adjustments
•
Select TV SPEAKERS ON from AUDIO menu.
•
Set amplifier volume to minimum.
•
Adjust television volume to desired level.
•
Adjust amplifier volume to match the television.
•
Select SPEAKERS OFF & VARIABLE AUDIO OUT from
AUDIO menu.
•
Volume, mute, bass, treble and balance are now
controlled through the television.
Note:
Select SPEAKERS OFF & FIXED AUDIO OUT to control
audio functions through the external amplifier.
Front Control Panel
Use the front panel of the television to use the TV without
remote or to use the Audio/Video input jacks for optional
equipment.
Procedure
•
Press TV/VIDEO to select VIDEO 3 input mode.
Note:
The front control panel can be used to access menus
and switch video mode when the remote control is not
available.
COMPONENT VIDEO INPUT
TERMINALS ON BACK OF TV
INPUT 1
R-AUDIO-L
COMPONENT
TO AUDIO
VIDEO INPUT
AMP
P
P
Y/VIDEO
R
B
L
INPUT 2
S-VIDEO
R
R-AUDIO-L VIDEO
, and P
B
color
inputs
provide
TERMINALS ON BACK OF TELEVISION
INPUT 1
R-AUDIO-L
COMPONENT
TO AUDIO
VIDEO INPUT
AMP
P
P
Y/VIDEO
R
B
L
INPUT 2
S-VIDEO
R
R-AUDIO-L VIDEO
.
R
Publicité
Chapitres
Table des Matières
Dépannage
