Product Description And Specifications - Bosch GHG 600 CE Professional Notice Originale

OBJ_BUCH-228-004.book Page 10 Wednesday, September 14, 2016 3:02 PM
10 | English
 Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
 Always wear safety goggles. Safety goggles will reduce
the risk of injuries.
 Disconnect the plug from the socket outlet before mak-
ing any adjustments, changing accessories, or placing
the power tool aside. This safety measure prevents unin-
tentional starting of the power tool.
 Check the power tool, cord and plug each time before
use. Do not use the power tool if damage is determined.
Do not open the power tool yourself and have it ser-
viced only by a qualified repair person using only origi-
nal spare parts. Damaged power tools, cords and plugs in-
crease the risk of electric shock.
Provide for good ventilation of your
working place. Gas and vapour developing
during working are often harmful to one's
health.
 Wear safety gloves and do not touch the hot nozzle.
Danger of burning.
 Never direct the hot air jet against persons or animals.
 Do not use the power tool as a hairdryer. The hot air being
blown out is significantly hotter than that from a hairdryer.
 When operating the power tool in damp environments
is unavoidable, use a residual current device (RCD).
The use of a residual current device (RCD) reduces the risk
of an electric shock.
 Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug when
the cable is damaged while working. Damaged cables in-
crease the risk of an electric shock.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The power tool is intended for the forming and welding of
plastic, removal of paint and the warming of heat-shrinkable
tubing. It is also suitable for soldering and tinning, loosening
of adhesive joints and the defrosting of water lines.
1 609 92A 2MS | (14.9.16)
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Nozzle
2 Heat protection collar
3 Thumbwheel for temperature control
4 On/Off switch with air-volume regulator
5 Standing surface
6 Wide jet nozzle*
7 Glass protection nozzle*
8 Reflector nozzle*
9 Welding rod*
10 Welding shoe*
11 Reduction nozzle*
12 Heat-shrinkable sleeve*
13 Angle nozzle*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Hot Air Gun
Article number
Rated power input
Air flow
Temperature at the nozzle
outlet (approx.)
Weight according to
EPTA-Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise Information
Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is lower than 70 dB(A).
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified on
the nameplate of the machine. Power tools marked
with 230 V can also be operated with 220 V.
Switching On and Off
To switch on the power tool, press the On/Off switch 4 to
position I or II.
To switch off the power tool, press the On/Off switch 4 to
the 0 position.
To save energy, only switch the power tool on when using it.
GHG 600 CE
0 601 942 1..
W 2000
l/min 350/550
°C 100–600
kg 1,1
/II
Bosch Power Tools