tau K206MA Notice D'installation page 18

5 - 6 STOP
7 - 8 CLOSE
7 - 9
PHOTOCELLS
7 - 10 SENSITIVE EDGE
11 - 12 **
AUX
12 - 13 **
TX PHOTOCELLS
FLASHING LIGHT
14 - 15 **
(LED CABINET)
ELECTROMAGNET
16 - 17* **
(VANDAL-PROOF)
16 - 18* ** BAR LED
19 - 20* 2 CH RADIO
nd
21 - 22
AERIAL
23 - 24 -
MOTOR
28 - 29
25 - 26 - 27 OPTIONAL
ENCODER
30 - 31 - 32 MAIN
ENCODER
* The outlets can be configured using the TAUPROG (see relative instructions). The standard con-
figuration is shown in the table.
** If Jumper 6 is not plugged in, energy saving mode will be activated and, at the end of each man-
ouvre, outputs 11-12, 12-13, 14-15, 16-17 and 16-18 will be switched off.
The terminal board for motor 2 (23-27) is to be used in support of the one for motor 1
(LUXE), or in case of fault/failure of the one for motor 1 (28-32), see wiring diagram.
18
STOP button N.C. input – Stops the bar in any position, temporar-
ily preventing the automatic closure, if programmed. Bridge the
connectors if not used.
(5= STOP - 6= COM )
CLOSE button N.O. input – Controls the total closure of the bar.
(7= COM - 8= CLOSE)
N.C. photocell input - it cuts in during the closing. Bridge the con-
nectors if not used.
(7= COM - 9= FOT)
Note: the photocell transmitter must always be supplied by
terminals no. 12 and no. 13, since the safety system test
(phototest) is carried out on it. Without this connection, the
control unit does not work. To override the testing of the
safety system, or when the photocells are not used, set dip-
switch no. 6 to OFF.
SENSITIVE EDGE input (resistive sensitive edge or fixed safety
edge); works only during closing and causes the bar to re-open
totally. Bridge the connectors if not used.
(7= COMMON - 10= SENSITIVE EDGE)
auxiliary circuits output 18 V DC max. 15 W for photocells, re-
ceivers, etc...
(11= NEGATIVE - 12= POSITIVE)
18V DC output for transmitter photocell – phototest - max. no. 1
photocell transmitters.
(12 = POSITIVE - 13 = NEGATIVE)
18V DC max. 20W output for flashing light supply, flashing signal
supplied by the control unit, rapid for closing, slow for opening.
(14 = POSITIVE - 15 = NEGATIVE)
Output for vandal-proof
Output for electromagnet to be connected to the end of the rod
to hold the barrier closed (vandal-resistant device). With the bar-
rier closed, the electromagnet is constantly powered. Every time
a command is given, the electromagnet is turned off before the
motor starts running.
(16= POSITIVE - 17= NEGATIVE)
bar LED power output.
(16=POSITIVE - 18= NEGATIVE)
2 radio channel output - for control of an additional automation
nd
or for switching on lights, etc... (N.O. clean contact)
Warning: to connect other devices to the 2nd Radio Channel
(area lighting, pumps, etc.), use an additional auxiliary relay
(see note at end of paragraph).
WARNING: the default outlet is active monostable 2 sec. To
switch it to active bistable or to modify the activation time
it is necessary to use the TAUPROG hand-held programmer
(see relative instructions).
plug-in radio-receiver aerial input , for 433.92 MHz receivers
only. (21 = GROUND - 22 = SIGNAL)
motor supply output 18V DC max. 50 W.
(23-28 = POSITIVE - 24-29 = NEGATIVE).
encoder supply and input (25 = WHITE signal - 26 = BLUE nega-
tive - 27 = BROWN positive).
encoder supply and input (30 = WHITE signal - 31 = BLUE nega-
tive - 32 = BROWN positive).
K206MA
18V DC, 3 W max;
See note below.
See note below.