Important - Valex MMotPot Instructions D'emploi

g
W e thank you for having purchased this product that will hereafter also be referred to as "tool".
Your new tool has been manufactured according to the highest quality standards, guaran-
teeing you long term service and safety.
Important! The illustrated chain saw is for pruning and must be used by operators
trained to maintain trees.
WARNING! Before using this tool, carefully read and follow the instructions in this
manual that refer to the diagrams and technical data contained in the enclosed sheet
in order to ensure that commissioning, starting, use, stopping, and maintenance are
carried out properly.
WARNING! Before using the tool, in order to ensure that correct commissioning, start-
up, use, stopping and maintenance are carried out correctly, please read carefully and
apply the following instructions. Before beginning work, you should be familiar with
the controls and safe use of this tool. Make sure you know how to stop it in case of an
emergency. Incorrect use of this tool could result in serious injury or death and damage
to property. Always consider your safety and the safety of others and act accordingly.
This tool was designed for non-professional use and should not be used for heavy duty or
continuous jobs or for commercial activities.
N.B.: this tool is made only to cut wood and must not be used on other materials.
Any use of this tool other than those indicated in these instructions may damage the
tool and create serious risk to both people and property.
WARNING! The engine works exclusively with an oil-petrol mixture in the percentage
indicated on the specification sheet. If this mixture is not used, irreparable damage
will be caused to the engine with immediate loss of warranty.
Please keep these instructions and the attached sheet in a safe place and have them
available for further reference if needed.
MACHINE DESCRIPTION (FIG. A)
1. Exhaust
2. Rear handgrip
3. Chainstay
4. Accelerator lever
5. Accelerator lever release button
6. Oil tank cap
7. Front hand grip
8. Front hand guard/ emergency chain brake lever
9. Start handle
10. Bar
11. Bar cover (where fitted)
12. Chain
14. Fuel tank cap
15. Chain tensioning screw (where fitted)
16. Bar fixing pin(s)
17. Bar fixing nut(s)
18. Housing
19. Sprocket
20. Chain tension pin (where fitted)
21. Bar groove
22. Bar lower hole
23. Oil hole
24. Air control lever (where fitted)
25. Engine off switch (where fitted)
26. Brake clutch unit
27. Internal combustion engine
28. Open cover lever.
29. Spacer for packaging
30. Spark plug
31. Air filter
32. Fuel priming pump (where fitted)
33. Hook (where fitted)
34. Air control and off lever (where fitted)
35. Carburetor Adjustments
36. Adjustment screw for chain lubrication oil
DESCRIPTION OF MARKS AND SYMBOLS (FIG. B)
1. Machine name
2. Technical data
3. Marks
5.

IMPORTANT!

6. Read the operating manual before using this tool
7. Always wear eye protection, ear plugs and helmet.
8. IMPORTANT! Read the safety measures to be taken in order to avoid the danger of
kickback
9. Important! Hot surfaces.
10. IMPORTANT! Risk of fire.
11. IMPORTANT! Always wear protective gloves. Always wear protective shoes. Wear
protective clothing
12. Noise level
13. Engine approval data
14. Warning! This is a pruning chain saw and must only be used by trained operators,
please read the instructions manual.
15. Mixture oil-petrol(if present)
16. Oil chain (if present)
17. Emergency Stop (if present)
18. Air valve in the carburetor
- 8 -
19. Adjust oil flow on chain
20. Warning! Wear gloves and protective shoes
21. Warning! Exhaust gas is dangerous to health
Tree maintenance operators must be trained to work safely. . Must have knowledge on the
use of security systems, first aid and have experience on the techniques of cutting trees.
1) DANGER OF FIRE AND EXPLOSION
WARNING! Risk of fire and explosion! Always switch the engine off before refilling.
The fuel and its fumes are highly inflammable. Do not pour the fuel onto hot surfaces.
Work in a well ventilated area, do not smoke and keep away from naked flames and
incandescent objects.
Use protective eyewear and anti-acid heavy duty gloves. Do not swallow, do not inhale
the fumes given off by the fuel and keep it out of the reach of children. Avoid contact
with the skin. In case of contact with the eyes wash with water and seek medical advice.
WARNING! Do not use the machine in areas with a risk of explosion and/or fire, in indoor
areas or in the presence of inflammable and/or explosive liquids, gases, powders,
vapours, acids or elements. Do not use the machine in the presence of incendiary
sources such as naked flames, cigarettes, sparks, etc.
An extinguisher must be located near the work area when using the chain saw.
2) EXHAUST GAS: RISK OF POISONING
WARNING! Risk of poisoning. The engine gives off poisonous, odourless and colourless
gas containing carbon monoxide: inhalation may cause nausea, fainting and death.
WARNING! Do not operate the machine in indoor or poorly ventilated environments. In
case of inhalation seek medical attention immediately.
3) HOT SURFACES: RISK OF BURNS
WARNING! Risk of burns. During use, some external surfaces of the machine may
reach high temperatures, and may remain hot for several hours after stopping the
engine. Pay particular attention to the exhaust system and the hot parts of the engine,
such as the cylinder head.
1. Keep the work area clean.
Begin cutting operations only after having cleaned the work area. There must also
be a firm support. Do not begin working until you have established a plan to escape
from the falling tree.
2. Consider the work area environment carefully.
Be cautious when cutting bushes and small saplings as their tender consistency may
cause them to become entangled in the chain, hitting you or throwing you off balance.
Never use the chain saw in areas where there is a danger of explosion, or near flammable
liquids or gases.Do not work near electrical wires or connections.
3. Keep children and other visitors at a safe distance.
Children and other visitors must maintain a safe distance from the work area and must
not touch the tool.
4. Storing the chain saw.
When not being used, these tools must be stored in a dry place, in a locked cupboard
out of the reach of children.
5. Do not force the chain saw or subject it to excessive pressure.
In order to guarantee better performance and safety the cut must be followed through
without exerting excessive pressure on the saw.
6. Correct use of this tool.
Use this tool only to cut wood. Do not use the chain saw on other materials.
7. Safe clothing.
Do not wear loose-fitting clothing or jewellery that may become entangled in the moving
parts of the chain saw. It is recommended that you use anti-slip safety shoes when
working outdoors. Always wear protective caps for long hair.
8. Use appropriate personal protective equipment.
Use safety glasses, safety shoes, comfortable clothing, protective gloves, and ear
and head protection.
9. Transporting the chain saw.
When not in use, transport the switched off chain saw by using the front hand grip.
Keep your fingers away from the switch and ensure that the bar and the chain are on
the back side. NB: Use the chain guard in order to avoid injury.
10. Working in safety.
Use clamps and trestles to work in safety.
11. Avoid unsafe movements.
Always make sure that your stance is supported and balanced.
12. Maintain your chain saw carefully.
Keep the tool sharpened and clean for better performance and safety. Follow the
instruction for lubrication and
dry, and free from oil and grease.
13. Switch off the chain saw.
Switch off the chain saw using the relevant control when not in use, when cleaning,
when tensioning or changing the chain, or when replacing accessories.
14. Removing the keys.
Before using, always check that all tools have been removed from the chain saw.
15. Avoid accidental starts.
Never transport the chain saw with the engine switched on. Ensure that the engine
switch is in the OFF '0' position.
16. Use caution while working.
Do not allow yourself to be distracted and always pay attention to what you are doing.
Use your common sense. Never use the machine when tired, ill or under the influence
of alcohol, drugs, or medicines that reduce alertness.
17. Check the damaged parts.
Before using the chain saw, always check the safety features and other potentially
damaged or worn parts carefully in order to determine if the chain saw is capable of
functioning correctly and long enough to complete the task at
WARNING!
changing the accessories. Keep the handles clean,
hand. Check