Maintaining The Appliance; Accessories - Dirt Devil BLADE24V Mode D'emploi

Maintaining the appliance

Emptying the dust collector
Press the wand release button (Fig
1
remove the reach wand or the accessory from the
handheld. Hold the handheld over a bin and press
2
the dirt release button (Fig.
lector cover opens and the dust falls out.
Cleaning the filters
CAUTION!
Use the appliance only with both filters in place.
NOTE:
For best cleaning results, tap the filters over a bin
every 4 – 6 uses and wash them every 3 months.
Empty the dust collector, > "Emptying the dust
1
collector" on page 19.
2
clockwise to unlock (Fig.
cover from the handheld.
ter (Fig. 13 / ) to remove it from the cover.
1
the round foam filter to remove it from the handheld.
Tap both filters over a bin to remove dirt.
5
out the filters under running water (max. 40 °C).
Leave the filters dry for at least 24 hours before
7
putting them back in the appliance.
Cleaning the separator
Empty the dust collector, > "Emptying the dust
1
collector" on page 19.
2
clockwise to unlock (Fig.
from the handheld. Press dust collector release
3
button to open the dust collector.
separator, push from inside the dust collector and
pull out the separator to remove (Fig.
ter out of the separator (Fig.
sepa- rator over a bin to remove dirt.
filter under running water (max. 40 °C).
ter dry for at least 24 hours before putting it back in
the appliance.
Removing blockages
▶
Carefully remove any hair from the turbo head
with a pair of scissors in order to remove any
blockages.
▶
Use a broomstick or similar blunt object to remove
blockages from the reach wand.
/ ) and
7
1
). ➔ The dust col-
/
11
1
Twist the filter cover anti-
) and remove the filter
12
Pull the tab on the fil-
3
Pull
4
Rinse
6
Twist the filter cover anti-
) and remove filter cover
12
To release the
4
). Pull fil-
14
5
15 ). Tap filter and
6
Rinse out the
7
Let the fil-
8
EN
Removing and replacing the brushbar
Press accessory release button and remove the
1
turbo head from the reach wand or the handheld
(Fig. 16 / ). Find the letter "A" on the base of the
1 2
turbo head to indicate the cover you need to remove
(Fig. / ). Use a screwdriver to unscrew the
17
A 3
three screws and remove the cover.
Slide the brushbar out of the housing (Fig.
4
Clear any blockages or replace the brushbar if it
5
is defective. Push brushbar onto the cover, slide
6
both parts in the housing (Fig.
cover with the screws.
Removing and replacing the belt
Press the accessory release button and remove
1
the turbo head from the reach wand or the hand-
held (Fig. / ).
16
1 2
the turbo head to indicate the cover you need to re-
move (Fig. / ).
17
B 3
the three screws and remove the cover.
is broken, remove it and slide a new one onto the
cogs (Fig. ). Refit the cover and tighten it with
20
5
the screws.

Accessories

• Crevice tool – 0777007 (Fig.
• Brushbar – 0777017 (Fig.
• Pre-motor filter – 0777001 (Fig.
• Wall mount – 0777006 (Fig.
• Filter set (separator + filter) – 0777002 (Fig.
• 24 V mains adapter – 0767004 (Fig.
• 32 V mains adapter – 0777004 (Fig.
• Pet tool – 0777009 (Fig.
• Dusting brush – 0777008 (Fig.
• Parquet tool – 0777011 (Fig.
Troubleshooting
Before you contact our Dirt Devil customer service
department or send the appliance to the Dirt Devil
customer service department, you will find a lot of
additional information in the service area of our web-
site which will help you solve problems.
www.dirtdevil.de/service
!
WARNING!
Switch off the appliance before you start trouble-
shooting. Never use a faulty appliance, mains
adapter or rechargeable battery.
) and tighten the
19
Find the letter "B" on the base of
Use a screwdriver to unscrew
If the belt
4
21 /A)
/B)
21
/C)
21
/D)
21
/F)
21
/F)
21
/G)
21
21 /H)
/I)
21
19
18 ).
21 /E)