Setting The Daily Program (Au Mode) - EINHELL BH 2000/1H Instructions D'origine

b) ECO mode (P)
If the equipment temperature which is mea-
sured at the integrated temperature sensor
and shown on the display falls below 7°C, the
heater switches on automatically.
If the equipment temperature which is measu-
red at the integrated temperature sensor and
shown on the display rises above 35°C, the
heater switches off automatically. The equip-
ment will heat with its minimum heat output.
c) Frost protection mode (R)
If the equipment temperature which is mea-
sured at the integrated temperature sensor
and shown on the display falls below 7°C, the
heater switches on automatically.
If the equipment temperature which is measu-
red at the integrated temperature sensor and
shown on the display rises above 9°C, the
heater switches off automatically.
To switch the equipment to the P1 – P7 heating
programs when it is switched on, press the "P/
PRO" button. "Fr" will fl ash in the display. To then
select the heating programs, repeatedly press the
+ or – buttons. The selected heating program will
be shown in the display (G).
The switch-off temperature in comfort and ECO
mode can be adjusted to suit your needs (see
6.3.1). If the equipment has switched off automa-
tically, "--" appears in the display (G).
Comfort mode (N) and ECO mode (P) is shown
by a bar (S / T) with 24 individual segments on
the display in each case. Each individual segment
represents 1 hour. These bars are shown on the
display in dependency on the set time (see sec-
tion 6.2.1) and the heating program. If no bar is
shown, this means that the equipment is in frost
protection mode.
6.3.1 Changing the heating programs
The preprogrammed P1 – P7 heating programs
can be changed to suit your individual needs,
starting with the current day, when the equipment
is switched on.
To perform the setting, proceed as follows:
•
Press the P/PRO button and then the + or
– button until the P1 – P7 program you want
flashes.
Anl_BH_2000_1H_SPK9.indb 20 Anl_BH_2000_1H_SPK9.indb 20
GB
The following example used to describe how to
adjust the settings is based on the selected pro-
gram P1.
•
Press the P/PRO button for 3 seconds while
P1 is flashing, until PROG and 00:00 (time)
appear in the display. Press the C/M button
once or several times to select the desired
comfort / ECO / frost protection mode or Off
for this time. Press the + or – button to select
the desired temperature in comfort or ECO
mode.
•
Note: The temperature in frost protection
mode is a fixed setting (7°C).
•
If you have selected Off, -- appears in the dis-
play.
•
To program for 01:00 (time), press the P/PRO
button and repeat the programming procedu-
re as described above for 00:00 (time). If you
want to use the same mode for the following
hour, press the P/PRO button again, etc.

6.4 Setting the daily program (AU mode)

In AU mode it is possible to assign a P1 – P7 pro-
gram for each separate day.
To do so, proceed as follows:
a) Press the P/PRO button; P1 will fl ash on the
display (G).
b) Press + or – until AU appears in the display
(G)
c) Press the P/PRO button for 3 seconds until
PROG appears in the display (K) and one of
the P1 – P7 programs fl ashes in the display
(G).
d) Press the C/M button; the day display (C) will
fl ash. Press the C/M button again to select a
day for which you want the program to apply.
e) Press the + or – buttons until the desired pro-
gram number (G) appears.
f) Wait for 5 seconds. The day (C) will have
been saved with the desired program number
(G).
g) Repeat steps c) – f) for the rest of the days.
6.5 "Windows open" function
The Item 16 button allows you to switch the
function on and off . If the temperature drops
considerably within a short time while the heating
function is switched on, the equipment switches
off automatically.
- 20 -
24.01.2019 12:53:55 24.01.2019 12:53:55