Setting The Desired Temperature - EINHELL BH 2000/1H Instructions D'origine

Explanation of the display (Fig. 7b)
A = Hour
B = Minute
C = Day
D = On
E = Locked
F = Heating
G = Program number
H = Windows open
K = Program
L = Timer
M = Temperature
N = Comfort mode
P = ECO mode
R = Frost protection mode
S = Bar for set comfort mode
T = Bar for set ECO mode
U = Time for set comfort / ECO mode
Note: Every press of a button is confi rmed by a
short audio signal.
The equipment will be locked to prevent changes
to settings if no operation is performed within one
minute when the equipment is switched on. The
"locked" symbol (E) will appear on the screen and
the backlighting of the display will go out. Press
button (16) and then press it again for 3 seconds.
The equipment is now unlocked. The "locked"
symbol (E) will go out and the display will be illu-
minated.
6.1 Switching the equipment on and off
Press the On/Off button (11). The equipment co-
mes on and the display will be activated. To switch
off , press the On/Off switch (11) again.
6.2 Manual operation
"Fr" is shown in the display. The equipment will
heat with the maximum heat setting, so long as
the equipment temperature exceeds the set desi-
red temperature. The S, T and F symbols will be
shown (Fig. 7b).
6.2.1 Setting the current day and time
•
Switch on the equipment as previously de-
scribed in 6.1.
•
Hour (A): Press the C/M button. Set the cur-
rent hour using the + and – buttons.
•
Minute (B): Press the C/M button again to set
the current minutes using the + and - buttons.
•
Day (C): Press the C/M button again to set
the current day using the + and - buttons. The
digit 1 corresponds to Monday, 2 = Tuesday,
etc.
Anl_BH_2000_1H_SPK9.indb 19 Anl_BH_2000_1H_SPK9.indb 19
GB
•
If you do not press a button for approx. 10
seconds, the last setting you made will be
saved.

6.2.2 Setting the desired temperature

Note: The desired temperature to be set corres-
ponds to the equipment temperature measured
on the integrated temperature sensor and shown
on the display. This may vary slightly from the ac-
tual room temperature. If the temperature exceeds
the set desired temperature, the heating function
switches off . If the temperature falls below the set
desired temperature, the heating function swit-
ches on again.
•
Switch on the equipment as previously de-
scribed in 6.1.
•
Press the + or - buttons. The temperature (M)
will be increased or decreased by 1°C each
time.
Note: A desired temperature between 15°C and
35°C can be set.
6.2.3 Setting the timer (ON time)
•
Switch on the equipment as previously de-
scribed in 6.1.
•
Press the C/M button for 3 seconds; the hour
(A) and minutes displays (B) will flash. Use
the + and – buttons to adjust the timer in 30
minute intervals.
•
If you do not press a button for approx. 5
seconds, the last setting you made will be
saved. The display for the timer setting (L) will
appear.
•
To switch off the timer, press the C/M button
again for 3 seconds. The display for the timer
setting (L) will go out.
Note: The ON time can be programmed to bet-
ween 00.30 h and 24.00 h.
6.3 Preprogrammed heating programs
Note: Seven diff erent preprogrammed heating
programs (P1 – P7) are available.
Three diff erent settings (modes) are available in
these heating programs.
a) Comfort mode (N)
If the equipment temperature which is measu-
red at the integrated temperature sensor and
shown on the display falls below 10°C, the
heater switches on automatically.
If the equipment temperature which is measu-
red at the integrated temperature sensor and
shown on the display rises above 35°C, the
heater switches off automatically. The equip-
ment will heat with its maximum heat output.
- 19 -
24.01.2019 12:53:55 24.01.2019 12:53:55