Tool Assembly - Milwaukee 2630-20 Manuel D'utilisation

Symbology
Direct Current
Underwriters Laboratories, Inc.
United States and Canada
Specifi cations
Cat. Volts No Load Blade
No. DC RPM Size
2630-20 18 3200 6-1/2"

TOOL ASSEMBLY

WARNING
Recharge only with
the charger specifi ed for the battery.
For specifi c charging instructions, read
the operator's manual supplied with
your charger and battery. This tool is
not compatible with V™-technology or
NiCd systems.
Inserting/Removing Battery Pack
Insert the battery pack by sliding battery
pack into the body of the tool. Insert the bat-
tery pack until the battery latches lock.
To remove the battery pack, press in both
battery latches and slide the battery pack
off of the tool.
WARNING
To reduce the risk
of injury, always remove battery pack
before changing or removing accesso-
ries. Only use accessories specifi cally
recommended for this tool. Others may
be hazardous.
Selecting Blade
Always use sharp blades. Dull blades tend
to overload the tool and increase the chance
of KICKBACK (see "Causes and Operator
Prevention of KICKBACK"). Only use thin
kerf blades with a maximum safe operating
speed greater than the no load RPM marked
on the tool's nameplate. Read the blade
manufacturer's instructions before use. Do
not use any type of abrasive cut-off wheel or
dry diamond cutting blades.
No Load Revolutions per
Minute (RPM)
Depth of Cut Depth of Cut
Arbor At 90° at 45°
5/8" 0 to 2-1/8" 0 to 1-9/16"
Installing and Removing Blades
1. Remove battery pack before installing
or removing blades.
2. Place the saw on a fl at surface with the
blade facing upwards. To remove the
bolt from the spindle, push in the spindle
lock button. While holding in the spindle
lock button, use the wrench provided
with the tool to turn the bolt clockwise.
Remove the bolt and blade fl ange.
3. Slide the lower guard lever up to raise
the lower guard. Remove the blade from
the spindle. Always clean the spindle,
upper guard and lower guard to remove
any dirt and sawdust.
NOTE: Do not remove inner blade
fl ange. Larger diameter of inner fl ange
(Fig. 1) should face the blade.
Bolt
Fig. 1
Spindle
Outer
Inner fl ange
fl ange
4. To install a blade, place the blade on
the spindle with the teeth pointing in the
same direction as the arrow on the lower
guard. Release the lower guard lever.
5. Place the blade fl ange on the spindle
and hand tighten the bolt.
6. While holding in the spindle lock button,
use the wrench to turn the bolt counter-
clockwise and tighten.
6
Adjusting Depth
1. Remove battery pack.
2. To adjust the depth of the cut, hold
the saw by the handle and loosen the
depth adjusting lever by pushing it down
toward the shoe (Fig. 2).
Fig. 2
3. Raise or lower the shoe to the desired
position. Markings in 1/4" increments
are located on the inner side of the
upper guard for depth setting. For the
proper depth setting, the blade should
extend no more than 1/8" to 1/4" below
the material being cut (Fig. 3).
1/4" ( 6 mm )
4. Lift the depth adjusting lever up towards
the motor housing to secure the shoe
position.
Adjusting Bevel Angle
1. Remove battery pack.
2. To adjust the angle of the cut, hold the
saw by the handle and loosen the bevel
adjusting knob (Fig. 4).
Fig. 4
3. Hold the front of the shoe and rotate the
saw by the handle to the desired angle
as indicated by the markings on the
bevel scale.
4. Tighten the bevel adjusting knob se-
curely.
Adjusting the Blade to Shoe
The shoe has been adjusted at the factory
to a 90 degree setting. Inspect the saw regu-
larly to make sure the blade is 90 degrees
to the shoe.
1. Remove battery pack.
2. Set the bevel pointer to zero.
3. To make sure the blade is 90 degrees to
the shoe, place saw on the blade side
and retract lower guard. Place a square
against the blade and shoe to inspect
the degree setting (Fig. 5).
Fig. 5 Bevel
adjustment
screw
4. To adjust the degree setting, loosen the
bevel adjusting knob. Turn the bevel
adjustment screw in or out until the blade
is at a 90 degree angle with the shoe.
5. Tighten the bevel adjusting knob se-
curely.
7