Hitachi C 10FSH Instructions De Sécurité Et Mode D'emploi page 23

Masquer les pouces Voir aussi pour C 10FSH:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

For bevel cut setting
Move handle on bevel section to the left and check that the position is stable and that the bevel angle
scale and the tip of the indicator are properly aligned. Then tighten the clamp lever.
To process crown molding at
Type of
positions 1 and 4 in Fig. 36.
Crown
Molding
Miter Angle
Setting
45° Type
right 35.3°
( mark)
38° Type
right 31.6°
( mark)
30° and 33.9° left slant setting method
Holder (A)
Fixing pin
Push
Bevel Scale
Indicator
(for left bevel scale)
Fig. 37
(1) Setting to cut crown moldings at positions 1 and 4 in Fig. 36 (see Fig. 38; tilt the motor head to the left):
1 Turn the turntable to the right and set the Miter Angle as follows:
* For 45° type crown moldings:
* For 38° type crown moldings:
2 Tilt the motor head to the left and set the Bevel Angle as follows:
* For 45° type crown moldings:
* For 38° type crown moldings:
3 Position the crown molding so that the upper surface (A in Fig. 35) contacts the fence as indicated
in Fig. 40.
(2) Setting to cut crown moldings at positions 2 and 3 in Fig. 36 (see Fig. 39; tilt the head to the left):
1 Turn the turntable to the left and set the Miter Angle as follows:
* For 45° type crown moldings:
* For 38° type crown moldings:
2 Tilt the head to the left and set the Bevel Angle as follows:
* For 45° type crown moldings:
* For 38° type crown moldings:
3 Position the crown molding so that the lower surface (B in Fig. 35) contacts the fence as in Fig. 41.
1
Miter Angle Scale
Bevel Angle
Setting
left 30°
( mark)
left 33.9°
( mark)
(1) Loosen the clamp lever and slant to the left a little at a time
Clamp Lever
while pushing the fixing pin into the main unit. At this time, the
fixing pin will enter one step and fit into the 30° left slant and
33.9° left slant setting slots.
(2) With the fixing pin in the slot as described above, setting to the
30° left slant position is possible by pushing to the right side.
(3) Also, with the fixing pin in the slot as described above, setting
to the 33.9° left slant position is possible by pushing to the left
side.
Tighten
(4) Look at the bevel scale and indicator to recheck whether or not
the settings match and then tighten the clamp lever.
Loosen
35.3° ( mark)
31.6° ( mark)
30° ( mark)
33.9° ( mark)
35.3° ( mark)
31.6° ( mark)
30° ( mark)
33.9° ( mark)
Head
Bevel Angle Scale
4
Fence
Base
Turntable
Fig. 38
To process crown molding at
positions 2 and 3 in Fig. 36.
Miter Angle
Bevel Angle
Setting
Setting
left 35.3°
left 30°
( mark)
( mark)
left 31.6°
left 33.9°
( mark)
( mark)
Head
Bevel Angle Scale
3
2
Fence
Miter Angle Scale
Fig. 39
Base
Turntable
English
23

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

C 10fsb

Table des Matières