3.2 Nominal Data; Data According To Commission Regulation (Eu) 327/2011; 3.4 Technical Description - Siemens SIMOTICS M-1PH8 Série Instructions De Service / Instruction De Montage

G3G280-BR04-M7

3.2 Nominal data

Motor M3G084-DF
Phase 3~
Nominal voltage / VAC 400
Nominal voltage 380 .. 480
range / VAC
Frequency / Hz
50/60
Method of obtaining ml
data
-1
Speed (rpm) / min 2700
Power consumption / W 530
Current draw / A
0.85
Min. ambient -25
temperature / °C
Max. ambient 60
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
01 Overall efficiency η / %
es
02 Measurement category
03 Efficiency category
04 Efficiency grade N
05 Variable speed drive
06 Year of manufacture
07 Manufacturer
08 Type
09 Power consumption P / kW 0.48
ed
09 Air flow q / m³/h
v
09 Pressure increase total p /
sf
Pa
10 Speed (rpm) n / min -1
11 Specific ratio *
12 Recycling/disposal
13 Maintenance
14 Additional components
*
Specific ratio = 1 + p / 100 000 Pa
fs
Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller
combination in a standardized measurement setup.
Item no. 56754-5-9970 · ENU · Change 213957 · Approved 2020-07-14 · Page 5 / 12
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Actual Req. 2015
66 47.2
A
Static
79.8 61
Yes
The year of manufacture is specified on the
product's rating label.
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart
· HRA 590344
D-74673 Mulfingen
G3G280-BR04-M7
1505
692
2710
1.01
Information on recycling and disposal is
provided in the operating instructions.
Information on installation, operation and
maintenance is provided in the operating
instructions.
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.

3.4 Technical description

Weight 15 kg
Size 280 mm
Motor size
84
Rotor surface Painted black
Terminal box material PP plastic
Electronics housing Die-cast aluminum, painted black
material
Impeller material PP plastic
Number of blades 6
Direction of rotation Clockwise, viewed toward rotor
Degree of protection
IP55
Insulation class "F"
Moisture (F) / H1
Environmental (H)
protection class
Installation position Any
Condensation None
drainage holes
Mode S1
Motor bearing Ball bearing; (sealed)
Technical features - Output 10 VDC, max. 10 mA
- Operation and alarm display
- External 24 V input (parameter setting)
- Alarm relay
- Integrated PID controller
- Motor current limitation
- PFC, passive
- RS-485 MODBUS-RTU
- Soft start
- EEPROM write cycles: 100,000
maximum
- Control input 0-10 VDC / PWM
- Control interface with SELV potential
safely disconnected from the mains
- Thermal overload protection for
electronics/motor
- Line undervoltage / phase failure
detection
Touch current
<= 3.5 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Electrical hookup Terminal box
Motor protection Thermal overload protector (TOP)
internally connected
Protection class I (with customer connection of protective
earth)
Conformity with EN 61800-5-1; CE
standards
Approval CSA C22.2 No. 77 + CAN/CSA-
E60730-1; EAC; UL 1004-7 + 60730-1
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
; Use the device in accordance with its degree of protection.
343