Operation - EINHELL TE-TS 2231 U Mode D'emploi D'origine

•
Fit the replacement table insert by following
the above in reverse.
6.10 Fitting and setting the splitter (Fig. 20)
•
Danger! Pull out the power plug.
•
Take out the table insert (see 6.9).
•
Set the blade (5) to max. cutting depth, move
to 0° position and lock in place.
•
Push the splitter (2) upwards.
•
The distance between the blade (5) and the
splitter (2) should be 3-5 mm.
•
Tighten the screw (z) and mount the table
insert.
6.11 Fitting/replacing the saw blade (Fig. 21)
Danger! Pull out the power plug.
Caution! Always wear gloves when handling
saw blades. Risk of injury!
•
Remove the table insert by undoing the coun-
tersunk head screws (see 6.9).
•
Undo the nut with the one wrench (30) on the
nut itself and an open-ended wrench (31) on
the flange to apply counter-pressure.
•
Important. Turn the nut in the direction of rota-
tion of the saw blade.
•
Take off the outer flange and pull the old saw
blade off the inner flange by dropping the bla-
de at an angle.
•
Clean the blade flange thoroughly before fit-
ting the new blade.
•
Mount and fasten the new saw blade in rever-
se order.
•
Warning! Note the running direction. The
cutting angle of the teeth must point in
running direction, i.e. forwards (see the
arrow on the blade guard).
•
Refit and set the splitter (2) and the saw blade
guard (4) (see 6.8.-6.10.)
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
6.12 Fitting the accessory slide
(Fig. 1, 2, 27-34)
•
The slide is available from retail stores as
a special accessory for this machine – it
is not included in the scope of this deli-
very.
•
On the bench-type circular saw: Remove the
guide rail for the universal stop (8).
•
Assemble the slide as shown in Figs. 27-32.
In doing so, make sure that both spacers
(110) are inserted between the profile (115)
and the slide plate (100). Allen key: Not sup-
Anl_TE_TS_2231_U_2831_UD_SPK7.indb 33 Anl_TE_TS_2231_U_2831_UD_SPK7.indb 33
GB
plied – available at retail stores.
•
Important: Do not screw the screw (108) in
too tightly. The stop must remain free moving
on the plate for the purposes of angle adjust-
ment.
•
The clamping lever (104) must be mounted in
such a way that the stop can be moved when
the clamping lever is released and is locked
when the clamping lever is secured. During
assembly, make sure that the spring washer
(114) is placed between the self-locking nut
(121) and the washer (123) (Fig. 31).
•
Screw the angles (103, 105) and struts (106,
107) to the bench-type circular saw (Fig. 32).
•
Place the slide on the guide rail (102) from
the front (Fig. 33).
•
If there is any slackness between the guide
rail and the running bearings of the slide pla-
te, then the lower bearing must be adjusted
using the screw (A), so that the slide can
glide freely.
•
Fit the Allen screws (111) to the front and rear
of the rail (102) together with the button (113)
and washer (117) (Fig. 34); they serve as a
limit stop.
•
The stop rail must move parallel to the saw
table at a distance of 1 mm. To achieve this,
loosely tighten the screws for the angles (103,
105) and struts (106, 107), then adjust the
rail in such a way that there is a 1mm gap
between the rail and the saw table in every
position. Now re-tighten the mountings.
•
Please note that for technical reasons relating
to delivery, some loose screws/washers may
be left over even if the slide is assembled and
fitted correctly (special accessory), because,
e.g. they may already be provided on the
bench-type circular saw.

7. Operation

7.1 ON/OFF switch and overload cut-out
(Fig. 1)
•
To turn the saw on, press the green button
„I". Wait for the blade to reach its maximum
speed of rotation before commencing with
the cut.
•
To turn the equipment off again, press the red
button „0".
- 33 -
23.04.14 08:39 23.04.14 08:39