EINHELL TE-TS 2231 U Mode D'emploi D'origine page 32

holes at the back, as this is where the struts
for the length extension table are to be faste-
ned later.
•
Mount the rubber feet (17, 21) on the legs.
•
Use the hex screws (40), spring washers
(39) and washers (37) to screw the extractor
connection (42) securely to the bottom of the
saw table.
•
Use the hex screws (41), washers (36) and
nuts (33) to screw the switch/plug block (44)
securely to the front side of the saw table.
•
Use the hex screws (41), washers (36) and
nuts (33) to screw the cross struts (18) and
longitudinal struts (20) loosely to the legs.
6.2 Chassis (Fig. 9, 11)
Use the hex screws (41) and washers (36) to
screw the chassis (19) to the rear legs.
6.3 Length extension table (Fig. 10-11)
•
Use the hex screws (41), washers (36) and
nuts (33) to fasten the lugs (22a,b) loosely to
the rear of the saw table.
•
Use the Allen screws (49) and nuts (32) to
fasten the length extension table (24) secure-
ly to the lugs.
•
Use the Allen screws (49) and nuts (32) to
fasten the struts (25) securely to the length
extension table.
•
Use the screws (41), large washers (35) and
nuts (33) to screw the struts (25) and loosely
to the rear legs.
•
Align the length extension table with the saw
table so that it is flat and then tighten all the fi-
xing points on the length extension table (24)
and the struts (25).
•
Caution! There is a risk of pinching when
folding down the length extension table (24).
Only hold the length extension table at the
rear end to fold it.
6.4 Guide rail for universal stop (Fig. 12-14)
•
Insert two screws (41) into each of the guide
rails (8,9).
•
Use nuts (34) to fasten one guide rail (8)
to the front of the saw table and another
guide rail (9) to the side of the saw table. Fit
washers (36) to each screw between the gui-
de rails and saw table when you do this.
•
Now stand the table on its feet. Align the
table so that it is level and then tighten all the
screws.
Anl_TE_TS_2231_U_2831_UD_SPK7.indb 32 Anl_TE_TS_2231_U_2831_UD_SPK7.indb 32
GB
6.5 Fastening to the surface (Fig. 15)
•
For greater stability, the saw needs to be se-
cured to a suitable surface.
•
Use the screws (41), washers (36) and nuts
(33) to fit the lugs (48) to the legs.
•
Afterwards connect the machine to the sur-
face using the holes in the lugs (connecting
material, e.g. screws/dowels are not included
in the scope of delivery – the connecting ma-
terial must be suitable for the surface and is
available at retail stores).
6.6 Holder for push stick/push block (Fig. 16)
Use two nuts (34) and washers (36) to fasten the
holder (27) to the hole in the front right leg.
6.7 Transport handles (Fig. 17)
Use the screws (41), washers (36) and nuts (33)
to fi t the transport handles (23) to the front legs.
6.8 Fitting the saw blade guard (Fig. 1, 18)
•
Fit the saw blade guard (4) in the oval hole
(y) in the splitter. Fasten the saw blade guard
using the screw (x) and tighten the screw only
enough to allow the saw blade guard to move
still.
•
Warning! The saw blade guard must always
be lowered over the workpiece before you
begin to cut.
•
To connect the suction hose of an extraction
system with a 100 mm connection, the cover
(3) on the saw blade guard can be removed
(extraction system not included).
•
If you use an extraction system: Connect the
36 mm extractor connection on the saw blade
guard to the extractor connection (42) with
the help of the suction hose (38). Connect the
vacuum extraction system to the 100 mm of
the extractor connection (42).
•
The machine is not allowed to be used wit-
hout the saw blade guard.
6.9 Replacing the table insert (Fig. 19)
•
The table insert has to be opened if you need
to replace it if it gets damaged and whenever
you change the blade or set the splitter.
•
To prevent increased likelihood of injury, you
should replace the table insert whenever it is
worn or damaged.
•
Important. Pull out the power plug.
•
Remove the saw blade guard (4).
•
Open the countersunk head screws (43) on
the table insert.
•
Take out the table insert (15).
- 32 -
23.04.14 08:39 23.04.14 08:39