Transport; Maintenance; Storage - Scheppach 3901218901 Traduction Des Instructions D'origine

8.8 Limiting the cutting depth (Fig. 3/13)
• The cutting depth can be infinitely adjusted using the
screw (25). To do this loosen the knurled nut (d) on
the screw (25). Move the stop for the cutting depth
limitre (26) to the outside. Turn the screw (25) in or
out to set the required cutting depth. Then re-tighten
the knurled nut on the screw (25).
• Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 1)
The saw is equipped with a debris bag (18) for saw-
dust and chips.
Squeeze together the metal ring on the dust bag and
attach it to the outlet opening in the motor area.
The debris bag (18) can be emptied by means of a zip-
per at the bottom.
8.10 Changing the saw blade (Fig. 14-17)
Remove the power plug!
Important.
Wear safety gloves when changing the saw blade.
Risk of injury!
• Swing up the machine head (4).
• Undo the screw (g) on the guide bar (35), so that it can
move freely and be pivoted downwards.
• Loosen the screw (f) of the flange cover so that it is
free to move.
• Press the release lever (2). Swing up the saw blade
guard (5) to the point where the recess in the saw
blade guard (5) is above the flange bolt (29).
• Insert the allen key (e) in the flange bolt (29).
• Firmly press the saw shaft lock (31) and slowly rotate the
flange bolt (29) in clockwise direction. The saw shaft lock
(31) engages after no more than one rotation.
• Now, using a little more force, slacken the flange bolt
(29) in the clockwise direction.
• Turn the flange screw (29) right out and remove the
external flange (30).
• Take the blade (6) off the inner flange (32) and pull
out downwards.
• Carefully clean the flange screw (29), outer flange (30)
and inner flange (32).
• Fit and fasten the new saw blade (6) in reverse order.
• Important! The cutting angle of the teeth, in other
words the direction of rotation of the saw blade (6)
must coincide with the direction of the arrow on the
housing.
• Move the guide bar (35) into position and tighten the
screw (f; g) again.
• Before continuing your work make sure that all safety
devices are in good working condition.
• Important! Every time that you change the saw blade
(6), check to see that it spins freely in the table insert
(10) in both perpendicular and 45° angle settings.
• Important! The work to change and align the saw
blade (6) must be carried out correctly.
26 GB/IE
8.11 Using the laser (Fig. 18)
• To switch on: Move the ON/OFF switch of the laser
(34) to the "1" position. A laser line is projected onto
the material you wish to process, providing an exact
guide for the cut.
• To switch off: Move the ON/OFF switch of the laser
(34) to the "0" position.
8.12 Adjusting the laser (Fig. 19)
If the laser (33) ceases to indicate the correct cutting line,
you can readjust the laser. To do so, open the screws
(36) and set the laser by moving sideways to that the
laser beam strikes the teeth of the saw blade (6).

9. Transport

• Tighten the set screw (26) in order to lock the rotary
table (14)
• Activate the release lever (3), press the machine
head (4) downwards and secure with the safety pin
(23). The saw is now locked in its bottom position.
• Fix the saw's drag function with the locking screw for
drag guide (20) in rear position.
• Carry the equipment by the fixed saw table (15).
• When reassembling the equipment proceed as de-
scribed under section 7.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time us-
ing a cloth. In order to extend the service life of the tool, oil
the rotary parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive products.
Brush inspection
Check the carbon brushes after the first 50 operating
hours with a new machine, or when new brushes have
been fitted. After carrying out the first check, repeat the
check every 10 operating hours.
If the carbon is worn to a length of 6 mm, or if the spring
or contact wire are burned or damaged, it is necessary
to replace both brushes. If the brushes are found to be
usable following removal, it is possible to reinstall them.

11. Storage

Store the device and its accessories in a dark, dry and
frost-proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.