Scheppach 3901218901 Traduction Des Instructions D'origine page 25

• Position the angle stop (a) between the saw blade
(6) and the rotary table (15).
• Loosen the locknut (c). Adjust the adjusting screw
(27) until the angle between the saw blade (6) and
the rotary table (16) is 90 °.
• Retighten the locknut (c) to secure this setting.
• Finally, check the position of the angle display. If
necessary, loosen the pointer (20) with a cross-slot
screwdriver, set to the 0 ° position of the angle scale
(19) and tighten the retaining screw again.
8.3 Cross cut 90° and turntable 0° (Fig.7/8)
In the case of cutting widths up to approx. 100 mm it is
possible to fix the traction function of the saw with the
set screw (21) in the rear position. In this position the
machine can be operated in cross cutting mode. If the
cutting width is over 100 mm then it is necessary to en-
sure that the set screw (21) is loose and the machine
head (4) can move.
• Move the machine head (4) to its upper position.
• Use the handle (3) to push back the machine head
(4) and fix it in this position if required (dependent on
the cutting width).
• Place the piece of wood to be cut at the stop rail (17)
and on the turntable (15).
• Lock the material with the clamping device (7) on
the fixed saw table (16) to prevent the material from
moving during the cutting operation.
• Push down the release lever (2) to release the ma-
chine head (4).
• Press the ON/OFF switch (3) to start the motor.
• With the drag guide (22) fixed in place:
use the handle (1) to move the machine head (4)
steadily and with light pressure downwards until the
saw blade (6) has completely cut through the work
piece.
• With the drag guide (22) not fixed in place:
pull the machine head (4) all the way to the front.
Lower the handle (1) to the very bottom by apply-
ing steady and light downward pressure. Now push
the machine head (4) slowly and steadily to the
very back until the saw blade (6) has completely cut
through the work piece.
• When the cutting operation is completed, move the
machine head back to its upper (home) position and
release the ON/OFF button (3).
Attention! The machine executes an upward stroke
automatically due to the return spring, i.e. do not re-
lease the handle (1) after completing the cut; instead
allow the machine head to move upwards slowly
whilst applying light counter pressure.
8.4 Cross cut 90° and turntable 0° - 45° (Fig. 7/8)
The crosscut saw can be used to make crosscuts of 0°
-45° to the left and 0° -45° to the right in relation to the
stop rail.
• Loosen set screw (11).
• Detent lever (12) pull with the index finger upward.
• Use the handle (11) to adjust the rotary table (15)
to the desired angle. The pointer (13) on the rotary
table must match the desired angle on the scale (14)
on the fixed saw table (16).
• Re-tighten the set screw (11) in order to secure the
rotary table (15).
• Cut as described under section 8.3.
8.5 Precision adjustment of the stop for mitre cut
45° (Fig. 1/9/10)
• No stop angle included.
• Lower the machine head (4) and secure using the
locking bolt (24).
• Fix the rotary table (15) in the 0° position.
• Loosen the set screw (23) and use the handle (1) to
angle the machine head (4) 45° to the left.
• 45° - position angle stop (b) between the saw blade
(6) and rotary table (15).
• Adjust the adjusting screw (28) until the angle between
the saw blade (6) and rotary table (15) is precisely 45°.
• It is not necessary to fix this setting because it is
maintained by the spring pretension.
• Subsequently check the position of the angle indi-
cator. If necessary loosen the pointer (20) using a
Philips screwdriver, set to position 45° on the angle
scale (19) and re-tighten the retaining screw.
8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1/2/11)
The crosscut saw can be used to make mitre cuts of
0° - 45° in relation to the work face.
• Move the machine head (4) to the top position.
• Fix the rotary table (15) in the 0° position.
• Loosen the set screw (23 and use the handle (1)
to angle the machine head (4) to the left, until the
pointer (20) indicates the desired angle measure-
ment on the scale (19).
• Re-tighten the fixing screw (23).
• Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 2/4/12)
The crosscut saw can be used to make mitre cuts to
the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° to the left or 0° - 45° to the
right in relation to the stop rail (double mitre cut).
• Move the machine head (4) to its upper position.
• Release the rotary table (15) by loosening the set
screw (11).
• Using the handle (12), set the rotary table (15) to the
desired angle (refer also to point 8.4 in this regard).
• Re-tighten the set screw (11) in order to secure the
rotary table.
• Undo the locking screw (23).
• Use the handle (1) to tilt the machine head (4) to the
left until it coincides with the required angle value (in
this connection see also section 8.6).
• Re-tighten the fixing screw (23).
• Cut as described under section 8.3.
GB/IE 25