Publicité
Les langues disponibles
Les langues disponibles
Fuel Gauge
To determine the amount of charge left in the bat-
tery, pull the trigger. The Fuel Gauge will light up
for 2-3 seconds.
To signal the end of charge, 1 light on the fuel gauge
will fl ash for 2-3 seconds.
LED
The sight-line window has an LED to allow for
better accuracy in dark areas. To turn on the LED,
press the fuel gauge button. To turn off the LED,
press and hold the fuel gauge button until the LED
goes off. The LED will go off automatically after
about a minute.
Using the Control Switch
The control switch may be set to three positions:
carriage open, cutting, and lock. Always allow the
motor to come to a complete stop before using the
control switch.
1. To insert or remove tubing, push the control
switch toward the carriage open
bol. Pull and release the trigger. The carriage
will return to the open position and the jaws will
unlock from the workpiece.
2. To cut, push the control switch toward the cutting
symbol. See "Cutting".
3. To lock the trigger, push the control switch to the
center position. The trigger will not work when
the control switch is in the locked position.
Always lock the trigger before storing the tool and
any time the tool is not in use.
WARNING
To reduce the risk of injury,
wear gloves when cutting. Cut tubing can
be sharp. Do not hold end of tubing. Cutter will
rotate tubing when trigger is pulled creating
a laceration hazard.
WARNING
Keep hands
away from all cutting edges
and moving parts. Fingers can
be pulled into cutting carriage and be cut or
crushed.
CAUTION
Do not cut off pieces of tubing
less than 1/2" long. Small pieces can be pulled
into moving carriage and damage tool
Lubrication points
Lubricating
To extend cutter life, use
Cutting wheel
a light oil to lubricate the
axle
cutting wheel axle, roll-
Mounting
ers, and mounting plate
Plate
when they appear dry.
Rollers
Cutting
The tubing cutter can cut copper tubing from 3/8"
to 1" (trade size). Always support the workpiece to
prevent rotating and moving during cutting.
1. Open the carriage
.
2. Insert the workpiece squarely between the
jaws.
3. Line up the cutting line with the cutting blade
using the sight-line window.
4. Slide the control switch to Cutting
5. Hold the tool and workpiece fi rmly to prevent
rotation and moving. Ensure the workpiece is
straight and centered in the jaws (see fi gures).
Keep thumb and hand away from jaws and cut-
ting carriage.
CORRECT
CORRECT
sym-
WRONG
WRONG
WRONG
WRONG
6. Pull and hold the trigger.
7. Release the trigger when the cut is complete.
8. Open the carriage
.
9. Remove the workpiece. Remove the battery pack
before removing small pieces where your fi ngers
are in or near the cutting carriage.
NOTE: Do not remove or insert the workpiece without
returning the carriage to the open position. Inserting/
removing workpieces while the carriage is in the cut-
ting position can damage the cutting wheel and jaws.
MAINTENANCE
WARNING
To reduce the risk of injury,
always unplug the charger and remove
the battery pack from the charger or tool
before performing any maintenance. Never
disassemble the tool, battery pack or charger.
Contact a MILWAUKEE service facility for ALL
repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good re-
pair by adopting a regular maintenance program.
After six months to one year, depending on use,
return the tool, battery pack and charger to a
MILWAUKEE service facility for:
• Lubrication
• Mechanical inspection and cleaning (gears,
spindles, bearings, housing, etc.)
• Electrical inspection (battery pack, charger,
motor)
• Testing to assure proper mechanical and
electrical operation
4
.
If the tool does not start or operate at full power
with a fully charged battery pack, clean the contacts
on the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to a MILWAUKEE service facility for repairs.
WARNING
To reduce the risk of per-
sonal injury and damage, never immerse your
tool, battery pack or charger in liquid or allow
a liquid to fl ow inside them.
Cleaning
Clean dust and debris from charger and tool vents.
Keep tool handles clean, dry and free of oil or grease.
Use only mild soap and a damp cloth to clean the
tool, battery pack and charger since certain cleaning
agents and solvents are harmful to plastics and other
insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use fl ammable or
combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and char-
ger to the nearest service center.
LIMITED WARRANTY - MEXICO,
CENTRAL AMERICA AND CARIBBEAN
TECHTRONIC INDUSTRIES' warranty is for 5 year since the original
purchase date. This warranty card covers any defect in material and
workmanship on this Power Tool.
To make this warranty valid, present this warranty card, sealed/stamped
by the distributor or store where you purchased the product, to the Au-
thorized Service Center (ASC). Or, if this card has not been sealed/
stamped, present the original proof of purchase to the ASC.
Call toll-free 1 800 832 1949 to fi nd the nearest ASC, for service, parts,
accessories or components.
Procedure to make this warranty valid
Take the product to the ASC, along with the warranty card sealed/
stamped by the distributor or store where you purchased the product,
and there any faulty piece or component will be replaced without cost
for you. We will cover all freight costs relative with this warranty process.
Exceptions
This warranty is not valid in the following situations:
a) When the product is used in a different manners from the end-user
guide or instruction manual.
b) When the conditions of use are not normal.
c) When the product was modifi ed or repaired by people not authorized
by TECHTRONIC INDUSTRIES.
Note: If cord set is damaged, it should be replaced by an Authorized
Service Center to avoid electric risks.
SERVICE AND ATTENTION CENTER
Rafael Buelna No.1.
Col. Tezozomoc Mexico, Azcapotzalco D.F.
Ph. 01 800 832 1949
IMPORTED AND COMMERCIALIZED BY:
TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.
Av. Santa Fe 481 piso 6, Col. Curz Manca.
CP 05349, Cuajimalpa, D.F.
Model:
Date of Purchase:
Distributor or Store Stamp:
ACCESSORIES
WARNING
Always remove battery
pack before changing or removing ac-
cessories. Only use accessories specifi cally
recommended for this tool. Others may be
hazardous.
For a complete listing of accessories refer to your
MILWAUKEE Electric Tool catalog or go online
to www.milwaukeetool.com. To obtain a catalog,
contact your local distributor or service center.
LIMITED WARRANTY - USA AND CANADA
Every MILWAUKEE power tool (including cordless product – tool, battery
pack(s) - see separate & distinct CORDLESS BATTERY PACK LIMITED
WARRANTY statements & battery charger and Work Lights*) is warranted
to the original purchaser only to be free from defects in material and
workmanship. Subject to certain exceptions, MILWAUKEE will repair or
replace any part on an electric power tool which, after examination, is
determined by MILWAUKEE to be defective in material or workmanship
for a period of fi ve (5) years* after the date of purchase unless otherwise
noted. Return of the power tool to a MILWAUKEE factory Service Center
location or MILWAUKEE Authorized Service Station, freight prepaid and
insured, is required. A copy of the proof of purchase should be included
with the return product. This warranty does not apply to damage that
MILWAUKEE determines to be from repairs made or attempted by anyone
other than MILWAUKEE authorized personnel, misuse, alterations, abuse,
normal wear and tear, lack of maintenance, or accidents.
*The warranty period for, Job Site Radios, M12™ Power Port and Trade Ti-
tan™ Industrial Work Carts is one (1) year from the date of purchase. The
warranty period for a LED Work Light and LEDUpgrade Bulb is a limited
LIFETIME warranty to the original purchaser only, if during normal use the
LED bulb fails the Work Light or Upgrade Bulb will be replaced free of charge.
*This warranty does not cover Air Nailers & Stapler, Airless Paint Sprayer,
Cordless Battery Packs, Gasoline Driven Portable Power Generators,
Hand Tools, Hoist – Electric, Lever & Hand Chain, M12™ Heated Jackets,
Reconditioned product and Test & Measurement products. There are
separate and distinct warranties available for these products.
Warranty Registration is not necessary to obtain the applicable warranty
on a MILWAUKEE power tool product. The manufacturing date of the
product will be used to determine the warranty period if no proof of
purchase is provided at the time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT
REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CON-
TRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT.
IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT
PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE
BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL
OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES,
EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSE-
QUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY
PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR
LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER
EXPRESS WARRANTIES, WRITTEN OR ORAL. TO THE EXTENT
PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WAR-
RANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WAR-
RANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT
PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED
TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS
DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the 'Service Center Search' in the Parts & Service section of
MILWAUKEE's website www.milwaukeetool.com or call 1.800.SAWDUST
(1.800.729.3878) to locate your nearest MILWAUKEE factory Service
Center location.
5
Publicité
