Noise Emission Values; Before Starting The Machine - EINHELL NHM 260/230 Mode D'emploi

Anleitung NHM 260-400-230_SPK1:Anleitung NMH 260-400-230_SPK1
whole pieces of square, rectangular or chamfered
converted timber.
The machine is to be used only for its
prescribed purpose.
Even when the machine is used as prescribed it is
still impossible to eliminate certain residual risk
factors. There is a risk of the following injuries in
connection with the required operation of the
machine.
Fingers or hands coming into contact with the
knife block in areas which are out of view.
Workpieces may kick back if the machine is used
incorrectly.
Damage to hearing and eye injuries plus injuries
to fingers and hands if the required protective
equipment is not used.
Harmful emissions when used in enclosed areas
without a suitable extractor system.

6. Noise emission values

NHM 260/400 - 260/230
Sound pressure level L
pA
Sound power level L
WA
The quoted values are emission values and not
necessarily reliable workplace values. Although
there is a correlation between emission and
immission levels it is impossible to draw any certain
conclusions as to the need for additional
precautions. Factors with a potential influence on
the actual immission level at the workplace include
the duration of impact, the type of room, and other
sources of noise etc., e.g. the number of machines
and other neighboring operations. Reliable
workplace values may also vary from country to
country. With this information the user should at
least be able to make a better assessment of the
dangers and risks involved.
7. Technical data of the NHM 260/400
AC motor:
Power P:
Power P:
Protection type:
Vibration a :
w
Max. workpiece width:
Max. workpiece height at thickness opening: 160 mm
Infeed table:
Planing table:
Thicknessing table:
Thicknessing feeding speed:
Idle speed of motor n
Idle speed of planing knives n
Max. planing cross-cutting depth:
Max. thicknessing cross-cutting depth:
Max. angle of the parallel stop:
Sawdust extractor:
Weight:
Operating mode S6 40%: Continuous operation with
idling (cycle time 10 minutes). To ensure that the
motor does not become excessively hot it may only
be operated for 40% of the cycle at the specified
rating and must then be allowed to idle for 60% of
the cycle.
7.1 Technical data of the NHM 260/230
Operation Idle speed
AC motor:
94.8 dB(A) 80.7 dB(A)
Power P:
104.8 dB(A) 91.1 dB(A)
Protection type:
Vibration a
Max. workpiece width
Max. workpiece height at thickness opening: 160 mm
Infeed table:
Planing table:
Thicknessing table:
Thicknessing feeding speed:
Idle speed of motor n
Idle speed of planing knives n
Max. planing cross-cutting depth:
Max. thicknessing cross-cutting depth:
Max. angle of the parallel stop:
Sawdust extractor:
Weight:
400V 3 ~ 50 Hz

8. Before starting the machine

1900 W S1
Unpack the surfacing and thicknessing plane and
2800 W S6 40%
examine it for any transit damage.
IP40
The machine has to be set up and aligned where
12 m/s²
it can stand securely.
260 mm All covers and safety devices have to be properly
fitted before the machine is switched on.
It must be possible for the planing knife to run
500 x 282 mm
02.10.2006 8:23 Uhr
500 x 282 mm
400 x 260 mm
:
0
:
0
230 V ~ 50 Hz
2000 W S1
:
w
500 x 282 mm
500 x 282 mm
400 x 260 mm
:
0
:
0
Seite 21
GB
5 m/min
2800 rpm
6500 rpm
3 mm
3 mm
45°
Ø 100 mm
92 kg
IP40
12 m/s²
260 mm
5 m/min
2800 rpm
6500 rpm
3 mm
3 mm
45°
Ø 100 mm
92 kg
21