Yamaha AW2400 Mode D'emploi page 274

Format des données MIDI
5.4. PROGRAM CHANGE (Cn)
< Reception >
If [Program Change Rx] is On, program change messages will be
received when [MIDI Rx Ch] matches. However, if [MIDI Rx Ch] is
OMNI, this message is received regardless of the channel.
A scene memory will be recalled according to the [PROGRAM
CHANGE TABLE] settings.
< Transmission >
If [Program Change Tx] is On, a program change will be transmitted
on the [MIDI Tx Ch] according to the [PROGRAM CHANGE
TABLE] settings when you recall a memory. If the recalled memory
number has been assigned to more than one program number,
the lowest-numbered program number will be transmitted.
STATUS 1100nnnn Cn
DATA 0nnnnnnn nn
5.5. MIDI TIME CODE QUARTER FRAME (F1)
< Transmission >
If [SYNC OUT] is set to MTC, Quarter Frame messages will be
transmitted according to the time code movements of the recorder
when the recorder is playing or recording.
< Reception >
This message is received if [MTC SYNC MODE] is set to SLAVE.
Quarter Frame messages received in realtime are internally assem-
bled into time code that controls the recorder.
STATUS 11110001 F1
DATA 0nnndddd dd
5.6. SONG POSITION POINTER (F2)
< Transmission >
If [SYNC OUT] is MIDI CLOCK, a song position message will be
transmitted when STOP or LOCATE is performed on the recorder,
to indicate the song position from which the song should start at the
next START or CONTINUE message.
STATUS 11110010 F2
DATA 0ddddddd dd0
0ddddddd dd1
5.7. TIMING CLOCK (F8)
< Transmission >
If [SYNC OUT] is MIDI CLOCK, this message is transmitted
according to the MIDI Tempo Map from when the recorder begins
playing or recording, until it stops.
STATUS 11111000 F8
5.8. START (FA)
< Transmission >
If [SYNC OUT] is MIDI CLOCK, this message is transmitted when
the recorder begins playing or recording at a location other than the
first measure.
STATUS 11111010 FA
5.9. CONTINUE (FB)
< Transmission >
If [SYNC OUT] is MIDI CLOCK, this message is transmitted when
the recorder begins playing or recording at a location other than the
first measure.
STATUS 11111011 FB
274
Mode d'emploi de l'AW2400
Program Change
Program No. ( 0-127)
Quarter Frame Message
nnn = message type (0-7) dddd = data
Song Position Pointer
data ( H) high 7 bits of 14 bits data
data ( L) low 7 bits of 14 bits data
Timing Clock
Start
Continue
5.10. STOP (FC)
< Transmission >
If [SYNC OUT] is MIDI CLOCK, this message is transmitted when
the recorder stops.
Stop
STATUS 11111100 FC
5.11. ACTIVE SENSING (FE)
< Reception >
Once this message is received, subsequent failure to receive any mes-
sage for a period of 300 ms will cause Running Status to be cleared,
and MIDI communications to be initialized.
Active Sensing
STATUS 11111110 FE
5.12. RESET (FF)
< Reception >
When a Reset message is received, MIDI communications will be
initialized by clearing Running Status etc.
Reset
STATUS 11111111 FF
5.13. EXCLUSIVE MESSAGE (F0-F7)
5.13.1. MMC
5.13.1.1. MMC STOP
< Transmission >
When the STOP key is pressed, this message is transmitted with a
device number of 7F.
< Reception >
If the AW2400 is operating as an MMC Slave, the transport will stop
when this message is received with a matching device number or a
device number of 7F.
System Exclusive Message
STATUS 11110000 F0
Real Time System Exclusive
ID No. 01111111 7F
Destination (00-7E, 7F:all call)
Device ID 0ddddddd dd
Machine Control Command (mcc) sub-id
Command 00000110 06
Stop (MCS)
00000001 01
EOX 11110111 F7 End Of Exclusive
5.13.1.2. MMC PLAY
< Reception >
If the AW2400 is operating as an MMC Slave, the transport will
begin playback when this message is received with a matching device
number or a device number of 7F.
System Exclusive Message
STATUS 11110000 F0
Real Time System Exclusive
ID No. 01111111 7F
Destination (00-7E, 7F:all call)
Device ID 0ddddddd dd
Machine Control Command (mcc) sub-id
Command 00000110 06
Play (MCS)
00000010 02
End Of Exclusive
EOX 11110111 F7
5.13.1.3. MMC DEFERRED PLAY
< Transmission >
This message is transmitted with a device number of 7F when the
PLAY key is pressed.
< Reception >
If the AW2400 is operating as an MMC Slave, the transport will
begin playback when this message is received with a matching device
number or a device number of 7F.
System Exclusive Message
STATUS 11110000 F0
Real Time System Exclusive
ID No. 01111111 7F
Destination (00-7E, 7F:all call)
Device ID 0ddddddd dd
Machine Control Command (mcc) sub-id
Command 00000110 06
Deferred play (MCS)
00000011 03
End Of Exclusive
EOX 11110111 F7