Nimh/Nicd Battery Program; Discharging Nicd/Nimh Battery; Charge-To-Discharge & Discharge-To-Charge Cycle Nimh/Nicd Battery - Konect PRODUO 80 Manuel D'utilisation

NIMH/NICD BATTERY PROGRAM

These programs are for charging or discharging NiMH (Nickel-Metal-Hydride) or NiCd (Nickel-Cadmium) battery
commonly used for R/C models applications. To alter the value at the display, press Start/Enter key to make
it blink then change the value using INC or DEC key. The value will be stored by pressing Start/Enter key once.
NiMH 2.0A 7.42V
CHG 022:45 00890
CHARGING NICD/NIMH BATTERY
NiMH CHARGE Aut
CUR LIMIT 5.0A
mode. But in "Man" mode, it will charge the battery with the charge current you set at the display. Each mode can
be switched by pressing INC and DEC button simultaneously when the current field is blinking.
The screen displays the current state of charging. To stop the process, press Batt type/Stop key once.
The audible sound indicates charge you the end of process

DISCHARGING NICD/NIMH BATTERY

NiMH DISCHARGE
1.0A 11.5V
NiMH 1.0A 7.42V
DSC 022:45 00890
To stop discharging press Batt type Stop key once. The audible sound indicates you at the end of process.
CHARGE-TO-DISCHARGE & DISCHARGE-TO-CHARGE CYCLE NIMH/NICD BATTERY
NiMH CYCLE
DCHG>CHG 3
NiMH 1.0A 7.42V
D>C 022:45 00890
DCHG 1 1314mAh
CHG 1 1430mAh
PB (LEAD-SULPHURIC ACID) BATTERY PROGRAM
This is programmed for charging Pb (lead-acid) battery with nominal voltage from 2 to 20V. Pb batteries are totally
different from NiCd or NiMH batteries. They can only deliver relatively lower current compare to their capacity,
and similar restrictions definitely apply to charge. So the optimal charge current will be 1/10 of the capacity. Pb
batteries must not be charged rapidly. Always follow the instruction is supplied by the manufacturer of battery.
When you are willing to alter the parameter value in the program, press Start/Enter key to make it
blink then change the value with INC or DEC key. The value will be stored by pressing Start/Enter key once.
To start the process, press Start/Enter button for more than 3 seconds.
This program simply charges the battery using the current you set. In "Aut" mode,
you need to set the upper limit of charge current to avoid from higher feeding current
that may damage the battery. Because some batteries of low impedance and small
capacity can lead to the higher charge current by the processor at automatic charge
Set discharge current on the left and final voltage on the right. The discharge
current ranges from 0.1 to 1.0A and the final voltage ranges from 0.1 to
25.0V. To start the process, press Start/Enter key for more than 3 seconds.
The screen displays the current state of discharge. You can alter the discharge
current by pressing Start/Enter key during the process. Once you change the
current value, store it by pressing Start/Enter button again.
Set the sequence on the left and the number of cycle on the right. You can use this
function for balancing, refreshing and break-in the battery. To avoid rising temperature
of the battery, there will a brief cool-off period that already fixed at "User setting" after
each charge and discharge process. The cycling number ranges from 1 to 5.
To stop the process, press Batt type/Stop key once. You can change the
discharge or charge current by pressing Start/Enter key once during the
process. The audible sound indicates you the end of process.
At the end of the process, you can see charged or discharged electric capacities of
the battery at each cyclic process.
By pressing INC or DEC button, the screen shows the result of each cycle in order.
29