Using Your Cleaner; Cleaner Maintenance - Hoover Power Capsule PC20PET 011 Manuel D'utilisation

GETTING TO KNOW YOUR CLEANER
A. Bag Door Release Latch
B. Cord Rewind Button
C. Parking slot
D. Exhaust Filter Cover
E. On/Off Button
F. Variable Power Control*
G. Bag Check Indicator
H. Bag Door
I. Main Cleaner
J. Hose
K. Hose Handle
L. suction Regulator
M. Telescopic Tube
N. Telescopic Tube Adjuster
GETTING TO KNOW YOUR CLEANER
Remove all components from the packaging.
1. Connect the hose to the cleaner main body, ensuring it locks into position. [1] To
release the hose: simply press the two latches on the hose end and pull.
2. Connect the hose handle to the upper tube end. [2]
3. Connect the tube lower end to the carpet and floor nozzle** or accessories if required. [3]

USING YOUR CLEANER

1. Extract power cord and plug it into the power supply. Do not pull the cord beyond
the red marker. [6]
2. Adjust the telescopic tube to the desired height by moving the telescopic tube adjuster
up and raise or lower the handle to the most comfortable cleaning position. [5]
3. Carpet and Floor Nozzle**: Press the floor type selector pedal* on the nozzle to
select the ideal cleaning mode for the floor type.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
Carpet & Floor Nozzle**: [4]
- Hard floor Cleaning: Press the pedal on the nozzle on Hard Floor mode and adjust the
slider on the nozzle on ALL FLOORs. In this position brushes, wheels and wiper blade
are lowered to protect hard floors. [4a]
- Standard Carpet & Rugs Cleaning: Press the pedal on the nozzle on Carpet mode
O. Floor Type selector Pedal*
P. Carpet and Floor Nozzle (GP) **
P1. Carpet Nozzle (CA) **
P2. Hard Floor Nozzle (HF) **
Q. Carpet and Floor Nozzle slider*
R. Pre-motor Filter
s. Pre-motor Filter Frame
T. Exhaust Filter
U. 2 in 1 Accessory
V. Pet Hair Remover Mini Turbo Nozzle*
W. Allergen Remover Mini Turbo Nozzle*
X. Parquet Nozzle*
Y. Parquet Extra Nozzle*
and adjust the slider on the nozzle on ALL FLOORs. In this position brushes and wiper
blade are raised while wheels are lowered to allow a perfect ease of movement on such
surfaces. [4b]
- Deep Carpet Cleaning: Press the pedal on the nozzle on Carpet mode and adjust the
slider on the nozzle on DEEP CARPET CLEANING. In this position brushes, wheels and
wiper blade are raised for a deeper cleaning of your carpet. [4c]
WARNING: It is recommended to avoid potential scratching of wooden floors that the
pedal is not set on Hard floor mode and the slider on Deep carpet cleaning.
switch the cleaner on by pressing the On/Off button on the cleaner main body. [7]
4.
Rotate Variable power rotary knob to increase or decrease the power. [8]
5.
Adjust the suction regulator to the desired level. [9]
6.
7. switch off at the end of use by pressing the on/off button. Unplug and press the cord
rewind button to wind the power cord back into the cleaner.
8. Parking and storage – The tube can be parked for temporary storage while in use, or in
the storage position when not in use. [10]

CLEANER MAINTENANCE

Replacing the Dust Bag
If the bag check indicator is red, please check and, if necessary, replace the bag.
Lift the bag door Latch to open the bag door and remove the bag. [11,12] The full
1.
dust bag should be disposed of correctly and carefully.
2. Fold a new bag as shown on the bag and fit by inserting the collar into the bag
holder.
3. Close the Bag door.
REMEMBER: The bag check indicator may be red if an obstruction has occurred. In this
case refer to 'Removing a Blockage From the system'.
Cleaning the Filter:
To maintain optimum performance of your cleaner, please wash the pre-motor filter and
exhaust filter after each 5 bag changes.
Cleaning the pre-motor filter:
1. Lift the bag door release latch to open the bag door and remove the bag. [11,12]
2. To remove the pre-motor filter slide the pre-motor filter frame from the cleaner. [13]
3. Remove the filter from the holder. [13]
4. Wash it in hand warm water [16], and allow it to dry [17] thoroughly before replacing
to the cleaner.
Cleaning the exhaust filter:
1. The remove the exhaust filter, unclip the exhaust filter cover and remove the exhaust
filter pack. [14,15]
2. Wash the filter in hand warm water [16] and allow it to dry [17] thoroughly before
replacing to the cleaner.
REMEMBER: Do not use hot water or detergents. In the unlikely event
of the filters becoming damaged, fit a Genuine Hoover replacement.
Do not try and use the product without a dust bag or filter fitted.
2
*Certain Models Only ** Certain models only, nozzles may vary according to model
GB