Using Your Cleaner; Before You Begin Cleaning; Accessories - Hoover SteamJet SMART Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 6
ASSEMBLING yOUR CLEANER
Remove all components from the packaging.
1.
Attach the hose to the main body of the cleaner. [2]
2.
Attach the extension tube to the hose handle. Connect the other extension tubes
together. [3]
3.
Attach the floor head connector to the floor head. Rotate the connector in place. [4]
4.
Attach the extension tubes to the connector until it clicks in place. [5]
Ensure the handle safety latch is locked. [6]
5.
NoTe: To remove the extension tube from the handle or the floor head from the tubes,
press the release latch and pull apart.

USING yOUR CLEANER

BefoRe you BeGIN CleANING

1.
Remove the clean water lid by pushing down and turning anti-clockwise. [7]
2.
Fill the measuring jug no more than the Max fill line.
Insert the funnel into the water tank and fill the unit with water. [8]
3.
4.
Replace the lid by pushing down and turning clockwise.
5.
Ensure the handle safety latch is locked. [6]
IMPORTANT: Always unplug the cleaner and press the steam release trigger to
release any remaining steam pressure before adding water.
Steam cleaning hard floors
1.
Ensure the floor head is connected to the extension tube.
2.
plug the steam cleaner into the main power and switch on. The red ON light will
illuminate. [9]
3.
After a few minutes the green Steam Ready light will illuminate indicating the cleaner
is ready for use. [10]
4.
Release the steam handle safety latch. [11]
5.
To produce steam press the Steam Trigger Button. [12]
6.
If necessary adjust the variable steam dial to adjust pressure. [13]
7.
Move the cleaner slowly backwards and forwards paying particular attention to high
traffic areas.
Refreshing carpets
IMPORTANT: Always unplug the cleaner and press the steam release trigger to
release any remaining steam pressure before adding water or changing a textile
pad or accessory tool.
1.
Place the floor head onto the floor cloth. [14]
2.
Lift the levers on either side of the floor head to secure each end of the floor cloth
in place. [15]
3.
Repeat steps 2-7 as detailed above.

ACCESSORIES

Ensure the handle safety latch is locked. [6]
1.
2.
To attach the concentration nozzle push onto the handle/extension tube until it
clicks in place. [16]
3.
push the desired small tool onto the concentration tool aligning the arrows. [17]
4.
Twist clockwise to secure in place. [17]
5.
plug the steam cleaner into the main power and switch on. The red ON light will
illuminate. [9]
6.
After a few seconds the green Steam Ready light will illuminate indicating the
cleaner is ready for use. [10]
7.
Release the steam handle safety latch. [11]
To produce steam press the Steam Trigger Button. [12]
8.
If necessary adjust the variable steam dial to adjust pressure. [13]
9.
NoTe: The concentration tool must be attached before fitting any other small tools.
Concentration Nozzle
Use on heavily soiled areas such as showers, kitchens. [18]
Window Squeegee
Use on windows and mirrors for a smear free clean. [19]
Upholstery Tool
Use the upholstery cloth over the window tool for use on sofas
and chair fabrics. [20]
large Round Brush
Use on stubborn grease and grime. [21]
metal Brush
For oven grills and racks. [22]
Angled Nozzle
For hard to reach areas such as taps etc. [23]
sCRApeR Tool
Ideal for dried residue in ovens or defrosting freezers. [24]
ImpoRTANT: AlWAys uNpluG THe CleANeR WHeN ADDING WATeR,
CHANGING A TexTIle pAD oR ACCessoRy Tool.
2
GB

Publicité

Table des Matières
loading

Table des Matières