Ryobi EBS-8021V Manuel D'utilisation page 6

GB
FR DE ES
DUST BAG (FIG. 2)
When sanding wood, the dust bag (5) should be used.
Although the dust bag has a substantial capacity,
it should be emptied frequently.
Opening the zipper of the dust bag allows complete
cleaning.
CAUTION!
When sanding metal, the dust bag should not be
used, because of the risk of fire from flying sparks.
CHANGING THE ABRASIVE BELT (FIG. 3 TO 4)
WARNING!
BE SURE TO DISCONNECT THE TOOL FROM
THE POWER SUPPLY WHEN MOUNTING AND
REMOVING THE SANDING BELT.
Place the tool on its side and lift the lever (3)
Q
to retract the front roller and release the belt tension
(Fig. 3).
Pull the sanding belt off.
Q
Mount a new sanding belt.
Q
NOTE! Be sure that the arrow inside of the belt is
pointing in the same direction as that of the tool.
Push the lever down to the original position (Fig. 4).
Q
CAUTION!
Ensure that your fingers are not trapped.
ADJUSTABLE FRONT HANDLE (FIG. 5)
FRONT HANDLE RELEASE BUTTON
Press the front handle release button (14) to allow
the front handle to be adjusted to the desired working
position.
FRONT HANDLE ADJUSTMENTS
While depressing the front handle release button move
the handle upwards or downwards to the desired angle
of either -15, 0, 15 and 30 degrees. Release the front
handle release button to allow the handle to lock in to the
selected.
OPERATING (FIG. 6)
NEVER COVER AIR VENTS SINCE THEY MUST
ALWAYS BE OPEN FOR PROPER MOTOR COOLING.
MAKE SURE THAT THE WORK PIECE IS FREE
OF NAILS AND OTHER FOREIGN OBJECTS THAT
COULD TEAR THE ABRASIVE BELT.
IT NL PT DK SE FI NO RU PL CZ
English
Hold the tool firmly with both hands. Turn the switch on and
permit the rotation of the abrasive belt to reach full speed.
Then gently place the tool on the work piece surface. Move
the tool back and forth. Never exert excessive pressure on
the tool. The weight of the tool applies adequate pressure.
Excessive pressure will retard the abrasive action, leave an
uneven finish and cause extra wear to both the tool and the
abrasive belt. Always lift the tool off the work piece before
turning the switch off.
LIVE TOOL INDICATOR
This tool features a live tool indicator (13) which
illuminates as soon as the tool is connected to the supply.
This warns the user that the tool is connected and will
operate when the switch is pressed.
AUTO BELT TRACKING SYSTEM
The machine is designed with auto-belt tracking system.
Turn the tool upside down and hold it firmly with one hand,
then start the tool and observe the tracking of the sanding
belt.
The edge of the sanding belt will automatically be even with
the outer edges of wear plate.
The system has been preset at the factory but may
required adjustment when belt are changed or an older
belt stretches. If the edge of the belt deviates more than
3.175mm (1/8 inch) from the edge of the wear plate, adjust
the belt by turning the auto-track adjusting screw until the
belt is even with the edge of wear plate.
CLAMP
(Optional accessory)
The clamp is designed to stabilize the tool when using it
in the bench configuration.
MOUNT & ADJUSTING THE OPTIONAL
SANDING FRAME
Put the sanding frame on the belt sander at attach four
slot into slot holder (15).
By turning the adjustment bolt clockwise, the sanding
frame will rise and can be taken out. If turning
counterclockwise, it will down and the depth will be
added.
MAINTENANCE
After use, check the tool to make sure that it is in good
condition. It is recommended that you take this tool to
a RYOBI Authorized Service Center for a thorough
cleaning and lubrication at least once a year.
2
HU RO LV LT EE HR SI SK GR TR