Publicité
Les langues disponibles
Les langues disponibles
P.32
___________________________________________________________________________________________________
PS10 & LS500 : SPECIFICATIONS, CURVES & DIAGRAMS
SYSTEM SPECIFICATIONS
Frequency Response [a]
Usable Range @-6dB [a]
Sensitivity 1W @ 1m [b]
Nominal Peak SPL @ 1m [b]
HF Dispersion [c]
Directivity : Q & DI [c]
Crossover Frequencies
Nominal Impedance
Recommended Amplifiers
SYSTEM OPERATION
Electronic Controller
Dispersion configuration
SubBass
Speaker Cables
PRODUCT FEATURES
Components : LF
[VLF]
HF
Height x Width x Depth
Weight : Net
Connectors
Construction
Fittings:
Handles
Front finish
Flying Points
Stand fittings
Fixed Installation
Power Supply
Dimensions & Weight
SHIPPING & ORDERING
Packaging
Shipping weight & Volume
PS SERIES MANUAL REV3 10/10/05
PS10 & LS500 : SPECIFICATIONS, CURVES & DIAGRAMS
PS10 with PS10 TDcontroller
65 Hz - 20 kHz ±3dB
58 Hz - 21 kHz
98 dB SPL Nominal - 96 dB SPL Wideband
124 to 127 dB Peak (for 200 to 500 W RMS Amp.)
50° to 100° Hor. x 55° Vert. Rotatable Horn, 4 positions
Q : 16 Nominal
DI : 12 dB Nominal ( f > 3 kHz )
2 kHz Passive
8 Ohms
200 to 500 Watts into 8 Ohms for 1 x PS10 per channel 400
to 1000 Watts into 4 Ohms for 2 x PS10 per channel
The PS10 TDcontroller is precisely matched to the PS10 & LS500 cabinets and includes sophisticated
protection systems. Using PS10 & LS500 without a properly connected PS10 TD will result in poor sound
quality and can damage the components.
After quick-release of the front grille from its fixings, the HF Horn can be rotated in 4 positions for dispersion
configuration.
The PS10 can be used without optional LS500 SubBass. Active two-way operation with the LS500 is included
in the PS10 TD. One LS500 matches 2 x PS10, additional LS500 may be used for enhanced effect.
PS10 are wired 2- & 2+ on Speakon connectors, LS500 on 1- & 1+. Loop through Speakons are present on
both. Single identical cables can thus be used to loop through combinations of up to 2 x PS10 & 1 x LS500 in
no particular order.
PS10
1 x 10" (25cm) 8 Ohm driver
1 x 1" throat driver + Low Distorsion,
Constant Directivity Asymetrical Dispersion Horn.
515 x 316 x 277 mm (20.28"x 12.44"x 10.91")
15 kg (33 Lbs)
2 x NL4MP Speakon 4 pole
Baltic Birch Ply finished with structured black coating
2 Metal recessed pockets
Acoustic foam on hex perforated steel grille (77%
transparent)
1 steel anchor plate for flying track on top (6 positions).
2 steel anchor plates for flying tracks on bottom (1 position)
Built in Steel Stand Fitting, 35mm (1"3/8)
Two sets of 4 fixing points (Omnimount 100 Std spacing)
for Horizontal or Vertical installation.
110/220 Volts (internal wiring), 50/60Hz.
1U 19" Rack.
190mm (7.5") Depth.
PS10's are packaged as pairs with PS10TD (Ref: PS10P+T) or without PS10TD (Ref : PS10P) in a single box.
Ref PS10P : 34 Kg (pair). Ref PS10P+T : 37 Kg (pair+processor). Shipping Volume : 0.169 m3 ( 5.96 cu feet)
Ref LS500 : 38 kg (unit) 0.238 m3 (8.41 cu feet)
LSub 500 with PS10 TDcontroller
40 Hz - 110 Hz ±3dB
38Hz - 120 Hz
101 dB SPL Nominal
131 to 134 dB Peak (300 to 800 W RMS Amp.)
-
-
120 Hz Active through PS10 TD
4 Ohms
300 to 800 Watts into 4 Ohms
LSub 500
1 x 15" (38cm) long excursion 4 Ohm driver
-
430 x 689 x 528 mm
20.79")
33 kg (73 Lbs)
2 x NL4MP Speakon 4 pole
Baltic Birch Ply & structured black coating
2 Metal recessed pockets
Perforated steel grilles
3 steel anchor plates for flying
tracks on sides and back
Internal Steel Stand Fitting on Top (35mm,
1"3/8) accepts a mast supporting 1 or 2 PS10's.
-
Earth-Lift (back panel)
2.9 kg (6.6 Lbs) net
(16.93"x 27.13"x
Publicité
Chapitres
