Before Starting The Equipment; General Information - EINHELL TE-MS 18/210 Li Traduction Du Mode D'emploi D'origine

5. Before starting the equipment

Warning!
Always remove the battery pack before
making adjustments to the equipment.
Be sure to read the following information before
you put the cordless equipment into operation:
•
Charge the battery pack with the charger.
An empty battery pack requires a charging
period of approximately 0.5 to 1 hour.

5.1 General information

•
The equipment must be set up where it can
stand securely, i.e. it should be bolted to a
workbench, a universal base frame or similar.
•
In the area of the machine's legs (34) there
is a fastening hole in each leg. Use them for
fastening standard screws, washers, spring
washers and nuts (not included in the scope
of this delivery - they are available from your
dealer). Fasten the machine on all four legs.
•
All covers and safety devices have to be
properly fitted before the equipment is
switched on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been
processed before, watch out for foreign
bodies such as nails or screws, etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted
and that the equipment's moving parts run
smoothly.
5.2 Assembling the saw (Fig. 1-5)
•
Fasten the transport handle (9) to the
machine head (4) using the supplied screws.
•
Insert the guide pins of the adjustable
workpiece supports (10) into the mounting
holes on the machine housing.
•
Tighten the fastening screw (42) at the
guide pins in order to secure the workpiece
supports against falling out.
•
To adjust the turntable (17), loosen the
locking screw (14) by approx. 2 turns, which
frees the turntable (17).
•
Turn the turntable (17) and scale pointer (15)
to the desired angular setting on the dial (16)
and lock into place with the locking screw
(14). The saw has locking positions at the
following angles: -45°, -40°, -35°, -30°, -22.5°,
-15°, -10°, -5°, 0°, 5°, 10°, 15°, 22.5°, 30°,
35°, 40° and 45°.
Anl_TE_MS_18_210_Li_SPK7_USA.indb 18 Anl_TE_MS_18_210_Li_SPK7_USA.indb 18
EN
•
To release the saw from its position at the
bottom, pull the retaining pin (25) out of the
motor mounting while pressing down lightly
on the machine head (4). Turn the fastening
bolt (25) through 90° before releasing it, so
that the saw remains unlocked.
•
Swing up the machine head (4).
•
The clamping device (8) can be fitted on the
left or right of the fixed saw table (18).
•
Always fasten the clamping device (8) with
the locking screw (26).
•
For the horizontal clamping of workpieces you
can anchor the clamping device in the holder
(33).
•
To move out the workpiece supports (10)
press the lever on the bottom side of
the workpiece support and then pull the
workpiece support outwards to the right or
left.
•
For repeat cuts of identical length you can
unfold the longitudinal stop (13).
•
When the locking grip (21) is undone, you
can tilt the machine head (4) to the left by up
to 45°.
5.3 Precision adjustment of the stop for
crosscut 90° (Fig. 1.6-7)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking grip (21) and tilt the
machine head (4) all the way to the right using
the handle (1).
•
Place the 90° angular stop (40) between the
blade (7) and the turntable (17).
•
Adjust the adjustment screw (29) until the
angle between the blade (7) and the turntable
(17) equals 90°.
•
Finally, check the position of the pointer (20)
on the scale (19). If the pointer (20) still does
not show the correct angle on the scale, it can
be readjusted.
•
To readjust it, undo the fastening screw on
the pointer (20) using a screwdriver. Move the
pointer to the desired scale position and then
retighten the fastening screw.
•
The angle stop (40) and hex key (41) are not
included in the scope of this delivery – they
are available from your dealer.
- 18 -
05.08.2019 14:05:51 05.08.2019 14:05:51