Initial Operation - Bosch Intuvia Notice Originale

English–2
 Remove the on-board computer when you park the
eBike.
It is possible to secure the on-board computer against remov-
al in the holder. To do so, remove the holder 4 from the han-
dlebar. Put the on-board computer in the holder. Screw the
locking screw 15 (thread M3, 8 mm long) from below into the
thread provided in the holder. Mount the holder back onto the
handlebar.
Operation

Initial Operation

Requirements
The eBike system can only be activated when the following
requirements are met:
– A sufficiently charged battery pack is inserted (see battery
pack operating instructions).
– The on-board computer is properly inserted in the holder
(see "Inserting and removing the on-board computer",
page English–1).
– The speed sensor is connected properly (see drive unit
operating instructions).
Switching the eBike System On/Off
Options for switching on the eBike system:
– If the on-board computer is already switched on when you
insert it into the holder, then the eBike system will be
switched on automatically.
– When the on-board computer and the eBike battery pack
are inserted, briefly press the On/Off button 5 of the on-
board computer.
– When the on-board computer is inserted, press the On/Off
button of the eBike battery pack (see battery pack operat-
ing instructions).
The drive is activated as soon as you step on the pedals (ex-
cept for in the push assistance function or in assistance level
"OFF"). The motor output depends on the settings of the as-
sistance level on the on-board computer. As soon as the sys-
tem is activated, "Active Line/Performance Line" will ap-
pear briefly on the display.
As soon as you stop pedaling when in normal operation, or as
soon as you have reached a speed of 25/45 km/h, the assis-
tance from the eBike drive is switched off. The drive is auto-
matically re-activated as soon you start pedaling again and the
speed is below 25/45 km/h.
Options for switching off the eBike system:
– Press the On/Off button 5 of the on-board computer.
– Switch the eBike battery pack off by its On/Off button (see
battery pack operating instructions).
– Remove the on-board computer out of its holder.
If the eBike is not moved and no button is pressed on the on-
board computer for 10 minutes, the eBike system will shut
down automatically in order to save energy.
1 270 020 XBI | (11.4.16)
eShift (optional)
eShift is the integration of automatic gear shifting systems in-
to the eBike system. To support the rider in the best way pos-
sible, the function indications and the basic settings menu
have been adapted for the "eShift" function.
eShift with NuVinci H|Sync
The optimum gear for the respective speed is automatically
set according to a pre-defined desired cadence. In manual
mode you can choose between multiple gears.
In the " NuVinci Cadence" mode you can use the "–" or
"+" button on the operating unit to increase or decrease the
desired cadence. If you hold down the "–" or "+" button, the
cadence will increase or decrease in steps of five. The desired
cadence is shown on the display.
In the " NuVinci Gear" mode you can use the "–" or "+"
button on the operating unit to switch back and forth between
several defined transmission ratios. The engaged transmis-
sion ratio (gear) is shown on the display.
eShift with SRAM DD3 Pulse
The gear hub of the SRAM DD3 Pulse works on a speed-de-
pendent basis. Regardless of which gear is engaged on the de-
railleur gears, one of the three gears of the gear hub will auto-
matically be engaged " Gear: Auto".
The engaged gear will be shown briefly on the display when-
ever the gear of the gear hub is shifted.
If the eBike is brought to a standstill from a speed of more
than 10 km/h, the system can automatically switch back to a
set "Start gear". The "Start gear" can be set in the basic set-
tings menu (see "Displaying/Adapting Basic Settings", page
English–5).
In the " Gear" mode you can use the "–" or "+" button on
the operating unit to switch back and forth between several
defined transmission ratios. The engaged transmission ratio
(gear) is shown on the display.
In the " Gear" manual mode, the system can also automati-
cally switch back to a set "Start gear".
The drive unit recognises the gear shift and briefly reduces
the motor assistance level as a result of it, which means the
gear can also be shifted at any time under load or on a hill.
eShift with Shimano Di2
For Shimano eShift you use the Shimano control lever to shift
gears.
The engaged gear will be shown briefly on the display when-
ever the gear of the gear hub is shifted.
The drive unit recognises the gear shift and briefly reduces
the motor assistance level as a result of it, which means the
gear can also be shifted at any time under load or on a hill.
If the eBike is brought to a standstill from a speed of more
than 10 km/h, the system can automatically switch back to a
set "Start gear". The "Start gear" can be set in the basic set-
tings menu (see "Displaying/Adapting Basic Settings", page
English–5).
Bosch eBike Systems