DeWalt DCD150 Instructions D’origine page 28

EnGLIsh
POWERSHIFT® Core Drill Stand. This tool is not intended to be
used for overhead or horizontal drilling upwards with an angle.
It is not intended to be used in rain.
DO nOT use under wet conditions or in presence of flammable
liquids or gases.
These diamond drills are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or mental
abilities; lack of experience, knowledge or skills unless they are
supervised by a person responsible for their safety. Children
should never be left alone with this product.
ANTI‑ROTATION System (Fig. A)
Your tool is equipped with the D
System. This feature senses the motion of the tool and shuts
the tool down if excessive. The red heavy load indicator and
ANTI‑ROTATION LED 5 illuminates when the ANTI‑ROTATION
System is engaged.
InDIcaTOR DIaGnOsIs
OFF Tool is functioning
normally
SOLID RED ANTI‑ROTATION
System has been
activated (ENGAGED)
Electronic Overload Warning (Fig. A)
The heavy load indicator and ANTI‑ROTATION LED
illuminate solid white as a warning when the tool is being
pushed too hard. When the load is reduced the heavy load
indicator and ANTI‑ROTATION LED will stop illuminating.
Continuing to use the tool after the LED is lit could cause the
tool to shut down or reduce run time.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect battery pack before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.

WARNING: Use only D
e
Fitting the Side Handle (Fig. C1–C3)

WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed. Failure to
do so may result in the side handle slipping during tool operation
and subsequent loss of control. Hold tool with both hands to
maximize control.
The side handle 7 clamps to the front of the gear case and
may be installed in multiple positions to permit right‑ or
left‑hand use.
1. Orient the side handle with the water supply fitting
towards the gear case.
26 26
WALT ANTI‑ROTATION
e
sOLUTIOn
Follow all warnings and instructions
when operating the tool.
With the tool properly supported,
release trigger. The tool will function
normally when the trigger is depressed
again and the indicator light will go out.
will
5
WALT batteries and chargers.
2. After the side handle is rotated into position, it should be
pushed rearward until the slots
are aligned and fully engaged with the projecting tabs
the gear case.
3. The side handle is then securely clamped by turning the
handle grip
13
Be sure to grip the side handle at the far end on the handle grip
to control the tool during a stall.
IMPORTanT: Figure C2 illustrates the correct installation and
Figure C3 illustrates two different incorrect installations of the
side handle.
Mounting and Removing a Core Bit to the Core Drill
(Fig. D)
This tool uses threaded core bits and adaptors which thread
directly onto the spindle
1. Choose the appropriate core bit for wet or dry drilling.
2. Follow the core bit manufacturer's recommendations for
mounting the accessory. For some smaller core bit sizes, you
will require an 1/2 BSP to 1/2 BSP (female to female) adaptor
to fit the bit onto the spindle. This adaptor is included with the
D WALT POWERSHIFT® DCD150 Core Drill Kit.
e
3. Hold the spindle using the supplied 32 mm wrench
and tighten the core bit
toward the drilling hole, using a customer supplied wrench
4. To remove the core bit, hold the spindle using the
supplied 32 mm wrench and loosen the core bit by rotating
clockwise, looking toward the drilling hole, using a customer
supplied wrench.

WARNING: Make sure the entire assembly is tight before
starting the operation.
Gear Selector (Fig. E)
The tool is fitted with a gear selector
torque ratio.
1. Release the switch and select the required position after the
motor has come to a complete standstill.
2. Always align the selector with the marks on the
gear housing.
3. Refer to the Technical Data to choose the appropriate speed
according to the diameter of the core bit and the material to
be drilled.
4. Do not change speed at full speed or during use.
Connecting to a Water Supply (Fig. F)
The water supply fitting
supply using quick‑connect.
1. To connect the quick‑connect hose to the water supply
fitting 9 place the end of the quick‑connect hose onto
the fitting.
2. Close the water tap
3. Connect an appropriate water supply system to the adaptor.
The DCE6820 D
water supply system.
4. Start water flow by rotating the water tap
and adjust to the necessary flow rate.
5. To remove the quick‑connect hose, pull back on the
quick‑connect collar
9 facing

WARNING: Make sure that the pressure of the water supply is
below the max. pressure as stated in Technical Data.
11 on the lip of the side handle
clockwise until tight.
6 of the core drill.
by rotating anticlockwise, looking
16
8 to vary the speed/
on this tool connects to a water
9
by rotating fully to the left.
18
WALT 18V XR Water Tank is the recommended
e
19 and remove the hose from the fitting.
12 of
14
.
15
to the right
18