Technical Data - Dewalt Dcd150 Instructions D’origine

EnGLIsh
CORE DRILL
DCD150
WARNING: Read all safety warnings, instructions,
illustrations, and specifications in this manual,
including the battery and charger sections provided in
an original tool manual or the separate Batteries and
Chargers manual. Manuals can be obtained by contacting
Customer Service (refer to the back page of this manual).

Technical Data

Type
No‑load speed
1st gear
2nd gear
3rd gear
Inside spindle thread
Outside spindle thread
Dust extraction adaptor thread
Max. water pressure
Minimum underpressure delivered by
the vacuum pump
Wireless tool control transmitter
Frequency Band
Max. Power (EIRP)
®
Bluetooth Transmitter
Frequency Band
Max. Power (EIRP)
Weight
DRILLING CAPACITIES
Drilling range in masonry
1st gear
Handheld
Stand
2nd gear
Handheld
Stand
3rd gear
Handheld
Stand
Drilling range in concrete (wet only)
1st gear
Handheld
Stand
2nd gear
Handheld
Stand
3rd gear
22 22
DCD150
1
min ‑1 0–700
min 0–1350
‑1
min ‑1 0–2500
Inside Thread 1/2"
Outside Thread: 1–1/4‑7"
1/2 BSP
bar 3
bar 0.75
MHz 433
mW 0.03
MHz 2400
mW 0.28
kg 5.5
Diameter
mm 76–100
mm 101–162
mm 38–100
mm 38–101
mm 12‑38
mm 12‑38
mm 51–72
mm 76–162
mm 38–72
mm 38–76
Handheld
Stand
Handheld
Noise values and vibration values (triax vector sum) according to EN 62841‑2‑1:
L (emission sound pressure level)
PA
L (sound power level)
WA
K (uncertainty for the given sound
level)
Drilling into concrete, wet
Vibration emission value a =
h DD
Uncertainty K =
The vibration and/or noise emission level given in this information
sheet has been measured in accordance with a standardised test
given in EN62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure.

WARNING: The declared vibration and/or noise emission level
represents the main applications of the tool. However, if the tool is
used for different applications, with different accessories or is poorly
maintained, the vibration and/or noise emission may differ. This may
significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and/or noise should
also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm (relevant for vibration),
organisation of work patterns.
EC‑Declaration of Conformity
Machinery Directive and Radio Equipment
Directive
Core Drill
DCD150
D WALT declares that these products described under
e
"technical data" are in compliance with:
2006/42/EC, EN62841‑1:2015 + A11:2022, EN 62841‑2‑1:2018 +
A11:2019 + A12:2022 + A1:2022.
These products also comply with Directive 2011/65/EU and
2014/53/EU.
The full text of the EU declaration of conformity can be
requested at the address below or is available at the following
internet address: www.2helpu.com (search by the Product and
Type Number indicated on the nameplate).
For more information, please contact D
address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of D
mm 12–38
mm 12–38
dB(A) 97
dB(A) 105
dB(A) 3.0
m/s 6.5
2
m/s 2 1.5
WALT at the following
e
WALT.
e