Charger Operation - DeWalt DCCS620 Guide D'utilisation

Masquer les pouces Voir aussi pour DCCS620:

Guide d'utilisation (42 pages)

Table Des Matières

Table des Matières

Les langues disponibles

English

Other types of batteries may overheat and burst

resulting in personal injury and property damage.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the charger can

be shorted by foreign material. Foreign materials

of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum

foil or any buildup of metallic particles should be

kept away from the charger cavities. Always unplug

the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before

attempting to clean.

Wireless Certifications and Safety

Information

•

This device is CAN ICES-3(B)/NMB-3(B) compliant.

•

This device complies with Part 15 of the FCC rules and

Industry Canada License-exempt RSS standard(s).

Operation is subject to the following two conditions:

ʵ This device may not cause harmful interference, and

ʵ This device must accept any interference

received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the

following measures:

ʵ Reorient or relocate the receiving antenna.

ʵ Increase the separation between the equipment

and adaptor.

ʵ Connect the equipment into an outlet on a circuit

different from that to which the adaptor is connected.

ʵ Consult the dealer or an experienced radio/TV

technician for help.

•

Changes or modifications to this equipment not expressly

approved by the manufacturer could void the user's

authority to operate the device. This Class B digital

apparatus complies with Canadian ICES-003.

•

Under Industry Canada regulations, this radio transmitter

may only operate using an antenna of a type and

maximum (or lesser) gain approved for the transmitter by

Industry Canada. To reduce potential radio interference

to other users, the antenna type and its gain should

be so chosen that the equivalent isotropically radiated

power (e.i.r.p.) is not more than that necessary for

successful communication.

•

To comply with FCC and Industry Canada RF radiation

exposure limits for general population, the antenna used

for this device must not be co-located or operating in

conjunction with any other antenna or transmitter.

For Bluetooth® Products

•

When traveling on airlines, be sure to comply with the

airline restrictions on usage of personal electronic devices

and Bluetooth®.

•

The out of range alert feature has been designed to act

as an aid to warn against products getting misplaced or

stolen. It is not a security system.

•

The connectivity range is up to 100 feet (30.5 meters)

depending on environment and location.

•

The shortwave radio frequency signals of a Bluetooth®

device may impair the operation of other electronic and

medical devices (such as pacemakers or hearing aids).

NOTE: The Bluetooth® word mark and logos are registered

trademarks owned by the Bluetooth®, SIG, Inc. and any use of

such marks by D

WALT is under license. Other trademarks and

trade names are those of their respective owners.

This product complies with these standards when operated

with a 6 foot (1.8 meters) or shorter extension cord.

Charging a Battery (Fig. C)

1. Plug the charger into an appropriate outlet before

inserting battery pack.

Fig. C

2. Insert the battery pack

the battery pack is fully seated in the charger. The red

(charging) light will blink continuously indicating that

the charging process has started.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is

fully charged and may be used at this time or left in the

charger. To remove the battery pack from the charger,

push the battery release button

nOTE: To ensure maximum performance and life of lithium-

ion battery packs, charge the battery pack fully before first use.