GE 26920 Guide D'utilisation

26920/26921
I
NTRODUCTION
40-Channel 900MHz
Cordless Telephone Your 900 MHz Cordless Telephone is designed to give you flexibility in use and high
quality performance. To get the most from your new cordless telephone, we suggest
User's Guide that you take a few minutes right now to read through this instruction manual.
IMPORTANT: Because cordless phones operate on electricity, you should have at least
one phone in your home that is not cordless, in case the power in your home goes out.
B Y B
EFORE OU EGIN
P C
ARTS HECKLIST
Make sure your package includes the items shown here.
TALK CHAN
RE/PA FLASH MUTE
1 ABC 2 DEF 3
CHARGE/
IN USE GHI 4 JKL 5 MNO 6
PQRS 7 TUV 8 WXYZ 9
0 #
PAGE * TONE OPER
ON OFF
VOL MEM
RINGER
Mounting
Base Handset bracket
M J R
ODULAR ACK EQUIREMENTS
You need an RJ11 (CA11A) type modular jack, which is the most common type
of phone jack and might look like the one pictured here. If you don't have a
modular jack, call your local phone company to find out how to get one
installed.
D S S
IGITAL ECURITY YSTEM
Your cordless phone uses a digital security system to provide protection against false
ringing, unauthorized access, and charges to your phone line.
When you place the handset in the base, the unit verifies its security code. After a
power outage or battery replacement, you should place the handset in the base for
about 20 seconds to reset the code.
INSTALLATION NOTE: Some cordless telephones operate at frequencies that may
cause interference to nearby TVs and VCRs. To minimize or prevent such
interference, the base of the cordless telephone should not be placed near or on top
We bring good things to life.
of a TV or VCR. If interference continues, moving the cordless telephone farther
away from the TV or VCR will often reduce or eliminate the interference.
I I
MPORTANT NFORMATION
This equipment generates and uses radio frequency energy which may interfere with
residential radio and television reception if not properly installed and used in
accordance with instructions contained in this manual. Reasonable protection against
such interference is ensured, although there is no guarantee this will not occur in a
given installation. If interference is suspected and verified by switching this equipment
I
NSTALLATION
on and off, the user is encouraged to try to correct the interference by one or more of
the following measures: Reorient the radio/television receiver's antenna, relocate the
equipment with respect to the receiver, plug the equipment and receiver into separate
D I
ESKTOP NSTALLATION
circuit outlets. The user may also wish to consult a qualified radio/television technician
for additional suggestions. This equipment has been fully tested and complies with all
limits for Class B computing devices pursuant to part 15 FCC Rules and Regulations.
This device complies with RSS-210 of Industry Canada. Operation is subject to the
following two conditions: (1) This device may not cause interference, and (2) This
5
device must accept any interference, including interference that may cause undesired
operation of the device.
3
I I
NTERFERENCE NFORMATION
This equipment generates and uses radio frequency energy which may interfere with
residential radio and television reception if not properly installed and used in
accordance with instructions contained in this manual. Reasonable protection against
such interference is ensured, although there is no guarantee this will not occur in a
given installation. If interference is suspected and verified by switching this equipment
on and off, the user is encouraged to try to correct the interference by one or more of
4
the following measures: Reorient the radio/television receiver's antenna, relocate the
equipment with respect to the receiver, plug the equipment and receiver into separate
circuit outlets. The user may also wish to consult a qualified radio/television technician
1.Make sure the mounting bracket is securely fastened to the bottom of the base. The
for additional suggestions. This equipment has been fully tested and complies with all
mounting bracket should be snapped into the upper four slots on the base's bottom.
limits for Class B computing devices pursuant to part 15 FCC Rules and Regulations.
This apparatus does not exceed the class B limits for RF noise emissions specified in 2.Set the RINGER switch (on the handset) to ON, and place handset in the cradle on the
the RFI regulations of the Industry Canada. base.
3.Plug the power supply into the power jack on the back of base and the other end into
H A C
EARING ID OMPATIBILITY
an AC outlet. The CHARGE/IN USE indicator comes on and indicates the battery is
This telephone system meets FCC standards for Hearing Aid Compatibility.
charging.
Allow the phone to charge for 12 hours prior to first use. If you don't properly charge
the phone, battery performance will be compromised.
4.Plug the telephone line cord into the TEL LINE jack on the back of the base and into a
INDUSTRY CANADA NUMBER IS LOCATED ON THE CABINET BOTTOM
modular phone jack.
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
5.Raise the base antenna.
NOTE: The phone automatically defaults to touch-tone dialing. To change to pulse
ATLINKS Communications Canada, Inc. (rotary) dialing, see "Tone/Pulse Dialing." If you don't know which type of service you
Model 26920R
(An Alcatel / Thomson Multimedia Joint Venture) have, check with the phone company.
15726710 (Rev. 0 E/F)
© 2001 ATLINKS Communications Canada, Inc.
01-05 Trademark(s) ® Registered
Printed in China Marque(s) ® déposée(s)
Downloaded from www.Manualslib.com
W M I M
ALL OUNT NSTALLATION UTE
Because it is necessary to charge the handset Use the MUTE button to interrupt a phone conversation to talk privately with someone
6
for 12 hours prior to connecting the phone for 5 else in the room.
7
use the first time, it is better to leave the unit
1.Press MUTE to activate mute feature (the BAT LOW/MUTE indicator blinks).
on a flat surface during initial charge before
2.Press MUTE again to turn it off.
attempting to hang it on the wall.
1.Turn the phone over and remove the
4 T
mounting bracket by pressing the tabs at the ONE
1
top of the bracket. Turn the bracket upside
This adjustment allows you to select tone (touch-tone) or pulse (rotary) mode dialing.
down and reattach it to the base by inserting
The phone is automatically set for touch-tone use.
the tabs into the lower four slots on the
3
bottom of the unit.
T
ONE
2.Set the RINGER switch (on the handset) to
1. Make sure the phone is OFF.
ON and place the handset in the cradle on
2.Press and hold the CHAN button for 2 seconds until the phone beeps.
the base.
3.Press TONE*.
3.Plug the power supply into the power jack on
2
the back of the base and the other end into
P
ULSE
an AC outlet. The CHARGE/IN USE indicator
comes on and indicates the battery is 1.Make sure the phone is OFF.
IN USE CHARGE/
charging.
2.Press and hold the CHAN button for 2 seconds until the phone beeps.
PAGE
Allow the phone to charge for 12 hours prior
3.Press #.
to first use. If you don't properly charge the
Headset (for Belt Clip (for
phone, battery performance will be compromised.
T
EMPORARY
26921 only) 26921 only)
4.Plug the telephone line cord into the TEL LINE jack on the back of the base and into a
modular phone jack.
This feature enables pulse (rotary) service phone users to access touch-tone services
offered by banks, credit card companies, etc., by pressing the TONE button to
5.Remove the handset hook; turn it upside down, and put it back in the slot (you need to
temporarily make the phone touch-tone compatible. To get information about your bank
do this to keep the handset from falling out of the base).
account, for example, you would:
6.Slip the mounting holes (on the bottom of the base and on the bracket) over the wall
1.Press the TALK button.
plate posts and slide the unit down firmly into place. (Wall plate not included.)
2.Call the bank's information line.
7. Raise the base antenna.
3.Press the TONE button after your call is answered.
NOTE: The phone automatically defaults to touch-tone dialing. To change to pulse 4.Follow the voice instructions to complete your transaction.
(rotary) dialing, see "Tone/Pulse Dialing." If you don't know which type of service you
5.Hang up when finished. The phone returns to pulse (rotary) service.
have, check with the phone company.
P
C P B
AGING THE
ORDLESS HONE ASICS
Press the PAGE button on the base to locate a
misplaced handset. When you press the PAGE
M C
AKING A ALL
button, the handset beeps. Press the TALK button
when you locate the handset.
After initial set up, put handset in the base for 12 hours to
charge the battery. NOTE: You can still page the handset with the
TALK ringer off.
The only two things you need to know to make a call are:
button
• Press the TALK button before you dial.
TALK
CHAN C
HANNEL
• Press TALK or place the handset in the base to hang up.
RE/PA FLASH MUTE
1 2 3
ABC DEF
If you ever experience any interference or don't have clear voice quality, press the
I U I 4 5 6
N SE NDICATOR GHI JKL MNO
RE/PA
CHAN button on the handset to advance to another channel.
PQRS 7 TUV 8 WXYZ 9
You know the phone is on when you see the IN USE button
TONE * OPER 0 #
M
indicator on the handset light. ON OFF
VOL MEM EMORY
RINGER
R
EDIAL
Store up to 10 numbers in memory for quick dialing.
Press the TALK button, then press the RE/PA (redial/pause)
button to redial the last number you called (up to 32 digits).
S
FLASH TORING A
MUTE
button button
M
R C EMORY
ECEIVING A ALL
2
1. Make sure the phone is OFF.
To answer a call, you must press the TALK button before you
can talk. 2. Press the MEM button
3.Dial the number (up to 20 digits).
F
LASH 4.Press MEM.
5.Press any number key (0-9) to store the phone number
Use the FLASH button to activate custom calling services
TALK in that memory location.
such as Call Waiting or call transfer, which are available CHAN
through your local phone company. RE/PA FLASH MUTE
1 2 3
ABC DEF
C
4 5 6 HANGING A
GHI JKL MNO
PQRS 7 TUV 8 WXYZ 9
TIP: If you press the TALK button to activate custom
TONE * OPER 0 # Use the same procedure to change a stored number as
1
calling services such as call waiting, you'll hang up the ON OFF
VOL MEM you do to store a number— you're just replacing the
RINGER
phone. Press FLASH instead. phone number with a different number.
S
V VOL button RINGER– ON TORING A REDIAL NUMBER
OLUME
OFF switch
1. Make sure the phone is OFF.
The VOL button controls the volume of the handset's
earpiece. 2.Press MEM.
3.Press RE/PA (redial/pause).
R S
INGER WITCH
4.Press MEM.
5. Press any number key (0-9) to store the phone number in that memory location.
The handset ringer switch can be set to ON or OFF. If the switch is off, the unit will not ring.
manuals search engine
S P M
TORING A AUSE IN EMORY
Use the RE/PA button to insert a pause when a delay is needed in the dialing sequence
(for example, when you must dial a 9 to get an outside line or when you must enter
codes to access your bank's information line). Each pause counts toward the 20-digit
limit.
If you need to dial 9 to get an outside line and want to store a number in memory
without having to dial 9 each time, you would:
/P D
ULSE IALING
1. Make sure the phone is OFF.
2.Press MEM.
3.Press 9.
4.Press RE/PA.
5.Dial the phone number you want to store in memory.
6.Press MEM.
7. Press any number key (0-9) to store the phone number in that memory location.
TIP: If you need a longer pause, press RE/PA button more times.
D S N
IALING A TORED UMBER
1.Make sure the phone is ON by pressing the TALK button.
T
ONE 2.Press MEM.
3.Press the number (0-9) for the desired memory location. The number dials
automatically.
IMPORTANT: If you make test calls to emergency numbers stored in memory, remain
on the line and briefly explain the reason for the call to the dispatcher. Also, it's a good
idea to make these calls in off-peak hours, such as early morning or late evening.
H B C O
EADSET AND ELT LIP PERATION
C
ONNECTING A
Headset plug
H
HEADSET TO THE
ANDSET
HANDSET
For hands free conversation, connect
IN USE CHARGE/
the headset (provided with 26921 only)
to the HEADSET jack as shown. The
PAGE
PAGE
handset receiver and microphone are
button
disabled when the headset is
connected.
B
UTTON Adjust the headset to rest comfortably
on top of your head and over your ear.
Move the microphone to approximately
2 to 3 inches from your mouth.
• Press the TALK button to answer or
place a call before using the headset.
C
CHAN button ONNECTING THE
N
UMBER IN B C
ELT LIP
There are two slots, one on each side of
the handset.
Slot for
• Attach the belt clip (provided with belt clip
26921 only) by inserting the sides of
the belt clip into the slots. Snap the
TALK CHAN
ends of the belt clip into place.
RE/PA FLASH MUTE
1 ABC 2 DEF 3
GHI 4 JKL 5 MNO 6
C B
PQRS 7 TUV 8 WXYZ 9 HANGING THE ATTERY
TONE * 0 #
OPER
S N ON OFF
TORED UMBER VOL MEM
Make sure the telephone is OFF before you replace battery.
RINGER
1.Remove the battery compartment door.
2.Disconnect the cord attached to the battery pack and
RE/PA MEM button
remove the battery pack from the handset.
button
3.Insert the new battery pack and connect the cord into the
jack inside the handset.
4.Put the battery compartment door back on.
5.Place handset in the base to charge. If you don't charge the
handset battery properly (for 12 hours) when you first set up
the phone and/or when you install a new battery pack, the
battery's long-term performance will be compromised.
B S P
ATTERY AFETY RECAUTIONS Problem
• Do not burn, disassemble, mutilate, or puncture. Like other batteries of this type, toxic BAT LOW indicator
materials could be released which can cause injury. stays on
• To reduce the risk of fire or personal injury, use only the battery listed in the User's
Guide.
Memory Dialing
• Keep batteries out of the reach of children.
doesn't work
• Remove batteries if storing over 30 days.
Contains
Nickel-Cadmium
Rechargeable Battery
NOTE: This product contains a nickel-cadmium rechargeable Unit locks up and
no communication
battery and must be recycled or disposed of properly. We suggest
between the base
that you check with your local Environmental Agency regarding
and the handset
recycling or disposal.
Ni-Cd
Must be Recycled or
Disposed of Properly
T G
ROUBLESHOOTING UIDE
S
ERVICE
In case of difficulty, please check the following Troubleshooting Guide before seeking
service.
ATLINKS Communications Canada, Inc. warrants to the purchaser or gift
recipient that if any manufacturing defect becomes apparent in this product
Problem Solution
within 1 year from the original date of purchase, it will be replaced free of
No dial tone • Check installation:
charge, including return transportation.
— Is the base power cord connected to a
working outlet?
This warranty does not include damage to the product resulting from
— Is CHARGE/IN USE indicator on?
accidents, misuse or leaking batteries.
— Is the telephone line cord connected to
the base unit and the wall jack?
Should your product not perform properly during the warranty period, either:
• Disconnect the base from the wall jack
1.Return it to the selling dealer with proof of purchase for replacement,
and connect another phone to the same
jack. If there is no dial tone in the second
phone, the problem might be your wiring
2.Remove the batteries (where applicable), and pack product complete with
or local service.
• Is the handset out of the base unit's accessories in the original carton (or equivalent).
range? Move closer to the base unit.
— Mail prepaid (with proof of purchase) and insured to:
• Make sure the battery is properly charged
HEADSET
(12 hours).
jack
• Is the battery pack installed correctly? ATLINKS Communication Canada, Inc.
c/o Thomson multimedia Ltd.
• If the phone still does not work, discon-
nect the power cord and remove the Distribution Centre
battery pack. Then reconnect the power
6200 Edwards Boulevard
cord and reinstall the battery pack. Place
Mississauga, Ontario L5T 2V7
handset in the base for 10 seconds to
The provisions of this written warranty are in addition to and not a modifica-
allow it to reinitialize.
tion of or subtraction from the statutory warranties and other rights and
Dial tone is OK, but • Make sure the tone/pulse setting is remedies contained in any applicable legislation, and to the extent that any
can't dial out programmed correctly.
such provisions purport to disclaim, exclude or limit any such statutory
warranties and other rights and remedies, such provisions shall be deemed to
Handset does not ring • Make sure the RINGER switch on the be amended to the extent necessary to comply therewith.
handset is turned to ON.
If you are unable to find a qualified servicer for out of warranty service, you
• You may have too many extension phones
may write to:
on your line. Try unplugging some
phones.
ATLINKS Communications Canda, Inc.
• See solutions for "No dial tone. "
c/o Thomson multimedia Ltd.
Cannot hear phone • Press the VOL button to adjust the P.O. Box 0944
conversation volume to the desired listening level. Indianapolis, Indiana, U.S.A., 46206-0944
Slot for
Attach your sales receipt to this booklet for future reference. This information
belt clip
You experience static, • Change channels. is required if service is needed during the warranty period.
noise, or fading in and out • Is handset out of range? Move closer to
PURCHASE DATE ________________________________________________
the base.
• Does the base need to be relocated?
NAME OF STORE ________________________________________________
• Charge handset battery.
• Make sure base is not plugged into an
REN N
UMBER
outlet with another household appliance.
On the bottom of this equipment is a label indicating, among other information, the FCC
Range is shorter • Press the CHAN button during the
than normal conversation to select a new channel. Registration number and Ringer Equivalence Number (REN) for the equipment. You
must, upon request, provide this information to your telephone company.
• Position the base antenna upward.
The REN is useful in determining the number of devices you may connect to your
Battery will not hold a • Be sure you are sufficiently charging the
telephone line and still have all of these devices ring when your telephone number is
charge or is fully charged battery. When the battery has been
called. In most (but not all) areas, the sum of the RENs of all devices connected to one
and the BAT LOW lights charged for 12 hours, you can expect
line should not exceed 5. To be certain of the number of devices you may connect to
approximately 4 hours of talk time.
your line as determined by the REN, you should contact your local telephone company.
• Check to be sure battery contacts on both
the handset and the base are making T N
ELEPHONE
contact and are clean; free of dirt or lint.
• When the handset is placed in the base,
Should your equipment cause trouble on your line which may harm the telephone
check that the base CHARGE/IN USE
network, the telephone company, where practicable, may notify you that temporary
indicator is on.
discontinuance of service may be required. Where prior notice is not practicable and
the circumstances warrant such action, the telephone company may temporarily
discontinue service immediately.
The telephone company may make changes in its communications facilities,
equipment, operations or procedures where such action is required in the operation of
its business. If these changes are expected to affect the use or performance of your
telephone equipment, the telephone company will likely give you adequate notice to
allow you to maintain uninterrupted service.
Notice must be given to the telephone company upon termination of your telephone
from your line.
Solution
• Place handset in base for 10 seconds to
reset the phone. If that doesn't work,
charge battery for 12 hours.
CATALOG NUMBER PRICE* QUANTITY TOTAL
DESCRIPTION
• Did you program the memory location keys
correctly?
• Did you follow proper dialing sequence?
• Make sure the tone/pulse setting is
programmed correctly.
• If the phone still does not work,
disconnect the power cord and remove
For credit card purchases
the battery pack. Then reconnect the
Your complete charge card number, its expiration date and your signature
power cord and reinstall the battery pack.
are necessary to process all charge card orders.
Place handset in the base for 10 seconds
to allow it to reinitialize. Copy your complete account number from your VISA card.
• If a power outage occurs while the
handset is away from the base, the
handset must be returned to the base
when the power returns. My card expires:
Copy the number above your name on
the Master Card
My card expires:
OR
____________________________________________________________________
Authorized Signature
*Prices are subject to change without notice.
Total Merchandise.........................................$_______________
Sales Tax........................................................$_______________
We are required by law to collect the appropriate sales tax for each individual state,
county, and locality to which the merchandise is being sent. Duties will apply for
shipments to Canada.
Use VISA or Master Card or Discover preferably. Money order or check must be in U.S.
currency only. No COD or Cash. All accessories are subject to availability. Where
applicable, we will ship a superseding model.
$5.00
Shipping/Handling........................................ $_______________
Total Amount Enclosed.................................$_______________
Mail order form and money order or check (in U.S. currency) made payable
to Thomson multimedia Inc. to:
Thomson multimedia Ltd
Mail Order Department
P.O. Box 8419
Ronks, PA 17573-8419
Name_______________________________________________________
Address_____________________________________ Apt.____________
City ________________________State________ ZIP_________________
Daytime Phone Number ( )_______________________________
Please make sure that this form has been filled out completely.
I
ETWORK NFORMATION